12 April 2023 in Nature Communications
VKVaithinathan Karthikeyan
+2
For decades, the widespread application of thermoelectric generators has been plagued by two major limitations: heat stagnation in its legs, which limits power conversion efficiency, and inherent brittleness of its constituents, which accelerates thermoelectric generator failure. While notable progress has been made to overcome these quintessential flaws, the state-of-the-art suffers from an apparent mismatch between thermoelectric performance and mechanical toughness. Here, we demonstrate an approach to potentially enhance the power conversion efficiency while suppressing the brittle failure in thermoelectric materials. By harnessing the enhanced thermal impedance induced by the cellular architecture of microlattices with the exceptional strength and ductility (>50% compressive strain) derived from partial carbonization, we fabricate three-dimensional (3D) architected thermoelectric generators that exhibit a specific energy absorption of ~30 J g−1 and power conversion efficiency of ~10%. We hope our work will improve future thermoelectric generator fabrication design through additive manufacturing with excellent thermoelectric properties and mechanical robustness.
26 September 2022 in ACS Applied Electronic Materials
30 August 2023 in Advanced Materials Interfaces
The terahertz frequency range is gaining popularity in security, stealth technology, and the future 6G network communication. For the control of severe terahertz electromagnetic interference (EMI) pollution, frequency‐selective stealth‐capable shielding materials are being explored to mask terahertz signals. For the realization of masking terahertz signals, the robustness, lightweight, and shape‐conformable materials with excellent terahertz EMI shielding/absorption are crucial. Here, the study reports the fabrication of 3D symmetric pyramidal architectural MXene composite films with frequency‐selective stealth performance characteristics via the facile drop casting method. With the high absorption capability of 2D MXene layers, the MXene composite films exhibit substantial terahertz stealth performance. 3D pyramidal microstructure design leads to frequency selective surface‐assisted reflection resonance in the frequency range of 0.6–1.1 THz. The MXene composite film demonstrates an outstanding maximum terahertz shielding effectiveness (SE) of up to 70.4 dB and a specific SE of 0.55 dB µm−1. These terahertz SE values exceed all of those for MX‐based shielding material designs reported in the literature. The investigation will open a new direction toward developing terahertz EMI shielding thin films with easy integration into any surface for stealth capabilities.
6 February 2024 in Advanced Materials Technologies
VKVaithinathan Karthikeyan
+2
23 December 2022 in Journal of Alloys and Compounds
15 December 2022 in ACS Omega
Recently, copper-based chalcogenides, especially sulfides, have attracted considerable attention due to their inexpensive, earth-abundance, nontoxicity, and good thermoelectric performance. Cu3SbS4 is one such kind with p-type conductivity and high phase stability for potential medium-temperature applications. In this article, the effect of a multiwalled carbon nanotube (MWCNT) on the thermoelectric parameters of Cu3SbS4 is studied. A facile synthesis route of mechanical alloying (MA), followed by hot pressing (HP) was utilized to achieve dense and fine-grain samples. Adding the optimal amount of MWCNT nanoinclusions in Cu3SbS4 enhanced the Seebeck coefficient by carrier energy filtering and reduced the thermal conductivity by strong phonon scattering mechanisms. This synergistic optimization helped achieve the maximum figure of merit (ZT) of 0.43 in the 3 mol % MWCNT nanoinclusion composite sample, which is 70% higher than the pristine Cu3SbS4 at 623 K. In addition, enhancement in mechanical stability is observed with the increasing nanoinclusion concentration. Dispersion strengthening and grain boundary hardening mechanisms help improve mechanical stability in the nanocomposite samples. Apart from the enhanced mechanical stability, our study highlights that the incorporation of multiwalled CNT nanoinclusions boosted the thermoelectric performance of Cu3SbS4, and the same strategy can be extended to other next-generation and conventional thermoelectric materials.