Ilgiz Galiev

Ilgiz Galiev

Auto-generated profile, based on publicly available information

Ilgiz Galiev

Kazan State Agrarian University

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2019 in Vestnik of Kazan State Agrarian University
Verified
Journal Article
Closed access
ИГИльгиз Галиев
Ильгиз Галиев
КХКамиль Хафизов
Камиль Хафизов
KKKamil Khafizov
Kamil Khafizov
ФХФарит Халиуллин
Фарит Халиуллин
FKFarit Khaliullin
Farit Khaliullin
A technically acceptable solution to the problem of increasing power is the use of a supercharger (compressor). This means that the air entering the engine is compressed before it enters the combustion chamber, i.e. the compressor provides the necessary amount of air, sufficient for complete combustion of the increased dose of fuel. Consequently, with the previous working volume of the engine combustion chamber and the same revolutions, we get more power, and the use of a turbocharger is a constructive solution to achieve this goal. However, due to the intensity of the operating mode of the turbochargers with a sharp change in the crankshaft rotation speed and load parameters during operation of the equipment (the rotor speed varies from 30,000 min-1 to 120,000 min-1, the exhaust gas temperature reaches 7500C) it requires effective lubrication of its bearings rotor. In this regard, in the lubrication system of the bearing assembly, a hydroaccumulator of membrane type was structurally provided. The article presents a constructive scheme of the connection of the hydroaccumulator in the lubrication system of the bearing pin of the turbocharger, presents photographs of the experimental setup to confirm the effectiveness of this design solution. The experiment was carried out after the engine stopped, operating at maximum, average and minimum crankshaft speeds, and the rundown time of the turbocharger rotor and pressure drop in the lubrication system of the turbocharger bearing assembly were measured from the moment the engine stopped. It was revealed that the installation of a hydroaccumulator in the lubrication system of the bearing assembly of the turbocharger will ensure the oil feed of the bearings with a sharp reduction in crankshaft rotation during engine overloads, which is confirmed by an increase in the overrun of the turbocharger rotor by 30 ... 40%, while the standard flow and oil pressure remain.

28 February 2020 in BIO Web of Conferences
Verified
Journal Article
Open access
PDF file
MFMarat Fashutdinov
Marat Fashutdinov
KKKamil Khafizov
Kamil Khafizov
IGIlgiz Galiev
Ilgiz Galiev
FGFanil Gabdrafikov
Fanil Gabdrafikov
FKFarit Khaliullin
Farit Khaliullin
In the article theoretical preconditions of a description of dynamics of manoeuvrability of machine-tractor, aggregates with a wheeled-tracked mover are considered. For a machine-tractor aggregate with half-tracked progress theoretical formulas of determination of an actual turning radius, the moment of resistance of turn and torque for rotation are obtained. The theoretical preconditions are confirmed by experimental research of the manoeuvrability of the machine-tractor aggregate with the tractor on a halftracked progress, made as the experimental sample. The dependences of the turn coefficient and the resistance coefficient of the turn are obtained, and the correlation coefficients and their significance have confirmed the existence of a stable connection between the changing parameter and the response function. Proceeding from theoretical and experimental research, it is possible to draw a conclusion that the manoeuvrability of the tractor with a wheeled-crawler mover does not concede to the tractor in the basic execution.

30 November 2020 in Vestnik of Kazan State Agrarian University
Verified
Journal Article
Closed access
IGIl'DUs Gimaltdinov
Il'DUs Gimaltdinov
BZBulat Ziganshin
Bulat Ziganshin
IGIlgiz Galiev
Ilgiz Galiev
ADAndrey Dmitriev
Andrey Dmitriev
AMAl'BErt Muhametshin
Al'BErt Muhametshin
AGAleksandr Gricenko
Aleksandr Gricenko
The research was carried out in order to develop a mathematical model and a diagnostic complex to determine the residual life of the rotor bearings of hammer crushers. Residual life information is essential for proactive maintenance and to prevent equipment crashes. To achieve this goal, Kazan State Agrarian University (Republic of Tatarstan) carried out calibration studies of the dependence of the diagnostic parameters of vibration on the value of the radial clearances of the bearings. 3610 bearings with different radial clearances (0.02 mm, 0.08 mm, 0.13 mm, 0.2 mm, 0.27 mm) were alternately installed on the rotor of the KD-2 hammer mill, from the drive pulley side and from the fan side) and recorded the vibration parameters. The information was read using a piezoelectric sensor. Signal processing was performed using a VVM-201 vibrometer. The results of mathematical processing of these data are presented in earlier publications. To determine the change in the value of the radial clearance from the operating time in hours, retrospective studies were carried out directly in the agricultural enterprises of the Republic of Tatarstan: “Shaimurzinskoe agricultural enterprise named after A.Sh. Abdreev” of Drozhzhanovskiy region, JSC “Kiyatskoe”of Buinskiy region, the agricultural production complex “Ural”of Kukmorskiy region, etc. The average operating time of the bearings of the rotor of the hammer-type KD-2 forage grinder before the onset of a pre-failure state on the drive side was 1900 ... 2000 hours, on the fan side - 2000 ... 2100 h. Based on the results of the research, the values of the radial clearances and vibration parameters of the rolling bearings of the rotor of hammer crushers were experimentally established, the regularities of the change in the radial clearance of the rolling bearings of the rotor of hammer crushers were revealed depending on the operating time. The developed mathematical models for determining the radial clearance in the rotor bearings of the hammer crusher by vibration parameters and calculating the residual life are implemented in a diagnostic complex consisting of a commercially available VVM-201 vibrometer and a residual life attachment

21 November 2021 in Vestnik of Kazan State Agrarian University
Verified
Journal Article
Closed access
IGIlgiz Galiev
Ilgiz Galiev
EPEkaterina Parlyuk
Ekaterina Parlyuk
BZBulat Ziganshin
Bulat Ziganshin
The problem of increasing the unit power of the engine without making changes to its design is solve by using a turbo supercharger. However, due to the intensity of the turbochargers operating mode, which are characterized by engine speed variability due to changing load indicators during operation (the number of rotor revolutions varies from 30000 min-1 to 120000 min-1, engine exhaust gases have a temperature of about 7500C), there is a need to improve the efficiency of the turbocharger bearing lubrication system. The purpose of the research is to ensure the operability and increase the reliability of turbochargers of diesel engines. To achieve this goal, a constructive solution for the lubrication system of the bearing assembly was propose, i.e., a membrane-type hydraulic accumulator was structurally provided in the lubrication system of the bearing assembly. Experimental studies were conduct to identify the operability and effectiveness of this constructive solution. The experiment was carried out on the KAMAZ-740 engine, the turbocharger shaft drive was carried out in normal mode, that is, from exhaust gases. L-02-40 fuel was use, SAE 10W–40 API was use as a lubricant. The turbocharger shaft speed varied from minimum to maximum by changing the engine speed and then stopping it. During the experiments, the following parameters of the turbocharger operation were measure: the duration of inertial rotation of the turbocharger rotor; the duration of pressure reduction in the turbocharger lubrication system. The dependences of the influence of the duration of the pressure drop in the turbocharger lubrication system and the duration of rotation of the turbocharger shaft by inertia with parallel inclusion of the accumulator in its lubrication system and in the normal mode of lubrication of the bearing are reveal. It is established that the installation of a device for feeding the turbocharger bearing during a sharp reduction in engine speed will increase the run-out of the turbocharger rotor from 30 to 65 s while maintaining the normal operating mode of the turbocharger lubrication system

7 November 2018 in Vestnik of Kazan State Agrarian University
Verified
Journal Article
Closed access
ГБГумар Булгариев
Гумар Булгариев
ГПГеннадий Пикмуллин
Геннадий Пикмуллин
ИГИльгиз Галиев
Ильгиз Галиев
ФСФарит Ситдиков
Фарит Ситдиков
БББагдат Бегалиев
Багдат Бегалиев
At the present stage of development of the country’s agro-industrial complex, the technological process of surface tillage by combined soil-cultivating machines, simultaneously combining a number of operations in one pass through the field, causes the presence in their designs of the necessary set of various promising working organs. In view of the foregoing, a rotary soil ripper with a spiral-plate working member equipped with radially directed teeth and connected by means of rods with end flanges has been developed. Also, the researched ripper has the limits of penetration of the working element in the form of flat discs equipped with flanges and the radial stop have the ability to rotate around their axes independently of the ripper shaft. An analytical study of the working units of this ripper was carried out from the point of view of the influence of their size and teeth on the process of interaction with the soil, on the basis of which some of their parameters were determined. In conclusion, it was concluded that the analytical equations obtained allow us to justify the choice of the most important design parameters of the proposed new design and design a toothed rotary working device that reduces to constructive implementation after calculating their basic dimensions.

30 October 2019 in Vestnik of Kazan State Agrarian University
Verified
Journal Article
Closed access
КХКамиль Хафизов
Камиль Хафизов
KKKamil Khafizov
Kamil Khafizov
РХРамиль Хафизов
Рамиль Хафизов
RKRamil Khafizov
Ramil Khafizov
АНАзат Нурмиев
Азат Нурмиев
ИГИльгиз Галиев
Ильгиз Галиев
To identify the main parameters of the tractor - its mass, engine power, wheel diameter and its profile width (four-parameter optimization) using the optimization criterion - the total energy costs (taking into account the energy of the crop lost due to the non-optimality of these parameters), it is necessary to have a mathematical model for calculation of engine power through the traction coefficient of performance of the tractor. The traction efficiency of the tractor is calculated through f is the coefficient of resistance to rolling of the tractor wheel and d is the coefficient of slipping of the tractor wheel. An analysis of the applied theory developed by previous researchers showed that the values f and d depend on the weight of the tractor coming to one wheel G, the diameter D and the width of the profile of the wheel B, the pressure in its tires ρw, the hardness of the soil H, the effort on the tractor hook Pkp and its speed V. During the analysis, it was found that the larger the diameter of the wheel, the width of the tire profile, the less the vertical load on the wheel and the pressure in the tires, the less the resistance to rolling the wheel over the soil being compacted. It is concluded that the study of the nature of the change in the coefficient of resistance to rolling wheels f and their slipping d from the above factors must be carried out jointly, because they influence each other. The absence of acceptable mathematical dependences for calculating the indicated coefficients, with the simultaneous action of all identified factors, leads to the need for a seven-factor experiment to identify the dependencies f =j (G, D, b, ρw, H, Ркр, V) and δ =ψ (G, D, b, ρw, H, Ркр, V), which is very difficult in operating conditions, therefore, using the similarity theory, it is necessary to reduce the number of factors in the experiment to four.