1 July 2004 in Journal of Hydraulic Engineering
This paper presents one of the first dedicated studies on mobile bed hydraulics of dam-break flow and the induced sediment transport and morphological evolution. A theoretical model is built upon the conservative laws of shallow water hydrodynamics, and a high-resolution numerical solution of the hyperbolic system is achieved using the total-variation-diminishing version of the second-order weighted average flux method in conjunction with the HLLC approximate Riemann solver and SUPERBEE limiter. It is found that a heavily concentrated and eroding wavefront first develops and then depresses gradually as it propagates downstream. In the early stage of the dam-break, a hydraulic jump is formed around the dam site due to rapid bed erosion, which attenuates progressively as it propagates upstream and eventually disappears. While the backward wave appears to migrate at the same speed as over a fixed bed, the propagation of the forward wavefront shows a complex picture compared to its fixed-bed counterpart as a ...
1 February 2008 in Proceedings of the Institution of Civil Engineers - Water Management
This paper describes benchmark testing of six two-dimensional (2D) hydraulic models (DIVAST, DIVASTTVD, TUFLOW, JFLOW, TRENT and LISFLOOD-FP) in terms of their ability to simulate surface flows in a densely urbanised area. The models are applied to a 1·0 km × 0·4 km urban catchment within the city of Glasgow, Scotland, UK, and are used to simulate a flood event that occurred at this site on 30 July 2002. An identical numerical grid describing the underlying topography is constructed for each model, using a combination of airborne laser altimetry (LiDAR) fused with digital map data, and used to run a benchmark simulation. Two numerical experiments were then conducted to test the response of each model to topographic error and uncertainty over friction parameterisation. While all the models tested produce plausible results, subtle differences between particular groups of codes give considerable insight into both the practice and science of urban hydraulic modelling. In particular, the results show that the terrain data available from modern LiDAR systems are sufficiently accurate and resolved for simulating urban flows, but such data need to be fused with digital map data of building topology and land use to gain maximum benefit from the information contained therein. When such terrain data are available, uncertainty in friction parameters becomes a more dominant factor than topographic error for typical problems. The simulations also show that flows in urban environments are characterised by numerous transitions to supercritical flow and numerical shocks. However, the effects of these are localised and they do not appear to affect overall wave propagation. In contrast, inertia terms are shown to be important in this particular case, but the specific characteristics of the test site may mean that this does not hold more generally.
1 March 2001 in Water Resources Research
1 February 2000 in Water Resources Research
31 May 2012 in Journal of Hydraulic Research
In this paper, the results of a benchmark test launched within the framework of the NSF–PIRE project “Modelling of Flood Hazards and Geomorphic Impacts of Levee Breach and Dam Failure” are presented. Experiments of two-dimensional dam-break flows over a sand bed were conducted at Université catholique de Louvain, Belgium. The water level evolution at eight gauging points was measured as well as the final bed topography. Intense scour occurred close to the failed dam, while significant deposition was observed further downstream. From these experiments, a benchmark was proposed to the scientific community, consisting of blind test simulations, that is, without any prior knowledge of the measurements. Twelve different teams of modellers from eight countries participated in the study. Here, the numerical models used in this test are briefly presented. The results are commented upon, in view of evaluating the modelling capabilities and identifying the challenges that may open pathways for further research.
1 October 2006 in Journal of Hydraulic Engineering
The Shields diagram remains the most widely used criterion for incipient motion of sediment. However its implicit nature makes applications rather inconvenient. By deploying Guo’s logarithmic matching method twice, this technical note develops an explicit formulation of the Shields diagram, enabling the critical Shields parameter to be determined directly from fluid and sediment characteristics without resorting to any trial and error procedure or iteration. An extended application of the logarithmic matching method is demonstrated.