1 July 2016 in Physics of Plasmas
Energy distribution and the flux of the ions coming on a surface are considered as the key-parameters in anisotropic plasma etching. Since direct ion energy distribution (IED) measurements at the treated surface during plasma processing are often hardly possible, there is an opportunity for virtual ones. This work is devoted to the possibility of such indirect IED and ion flux measurements at an rf-biased electrode in low-pressure rf plasma by using a “virtual IED sensor” which represents “in-situ” IED calculations on the absolute scale in accordance with a plasma sheath model containing a set of measurable external parameters. The “virtual IED sensor” should also involve some external calibration procedure. Applicability and accuracy of the “virtual IED sensor” are validated for a dual-frequency reactive ion etching (RIE) inductively coupled plasma (ICP) reactor with a capacitively coupled rf-biased electrode. The validation is carried out for heavy (Ar) and light (H2) gases under different discharge conditions (different ICP powers, rf-bias frequencies, and voltages). An EQP mass-spectrometer and an rf-compensated Langmuir probe (LP) are used to characterize plasma, while an rf-compensated retarded field energy analyzer (RFEA) is applied to measure IED and ion flux at the rf-biased electrode. Besides, the pulsed selfbias method is used as an external calibration procedure for ion flux estimating at the rf-biased electrode. It is shown that pulsed selfbias method allows calibrating the IED absolute scale quite accurately. It is also shown that the “virtual IED sensor” based on the simplest collisionless sheath model allows reproducing well enough the experimental IEDs at the pressures when the sheath thickness s is less than the ion mean free path λi (s < λi). At higher pressure (when s > λi), the difference between calculated and experimental IEDs due to ion collisions in the sheath is observed in the low energy range. The effect of electron impact ionization in the sheath on the origin and intensity of low-energy peaks in IED is discussed compared to ion charge-exchange collisions. Obviously, the extrapolation of the “virtual IED sensor” approach to higher pressures requires developing some other sheath models, taking into account both ion and electron collisions and probably including even a model of the whole plasma volume instead of plasma sheath one.
1 July 2021 in Plasma Sources Science and Technology
Ion-assisted surface processes are the basis of modern plasma processing. Ion energy distribution (IED) control is critical for precise material modification, especially in atomic-level technologies such as atomic layer etching. Since this control should be done in ‘real time’, it requires ‘real-time’ feedback using fast process sensors. In the general case of an industrial plasma reactor, when direct IED measurement is not possible, the IED can be estimated using the concept of a ‘virtual IED sensor’. In this paper, a similar ‘virtual IED sensor’ is considered using an asymmetric dual-frequency (df) rf CCP discharge as an example. It is based on a fast calculation method of the IED at an rf-biased electrode. This approach uses the experimentally measured sheath voltage waveform and plasma density (or ion flux) as input data, and also includes Monte-Carlo simulation of ion motion in the sheath to take into account the effect of ion-neutral collisions. To validate this approach, experiments were carried out using various plasma diagnostics in several gases: argon and xenon as examples of plasma with atomic ions and nitrogen as an example of plasma with molecular ions. It is shown that in all cases it is possible to obtain an adequate IED estimation, close to the experimental one, in a reasonably short time (∼tens of seconds when using a modern PC). The results obtained demonstrate the possibility of using a virtual IED sensor in real plasma processing.
31 January 2018 in Plasma Sources Science and Technology
Ion flux and plasma density are some of the most essential parameters for plasma-assisted process control. There is also a simple and well-known relation between them based on the Bohm criterion. This relation allows the avoidance of directly measuring both the ion flux and the plasma density simultaneously, but the question is, how accurate this estimation would be. This work represents the study of the sensitivity of the relation to plasma conditions, such as gas pressure, type of gas and plasma density. The experiments are carried out in an asymmetric rf dual-frequency CCP discharge in noble gases—Ar and Xe—and in molecular gas—N 2 . The gas pressure is varied from 20 mTorr up to 200 mTorr and the plasma density range is 10 9 to 5.6 × 10 10 cm −3 . Analysis of the experimental data is made by using the 2D PIC MCC model of the ion current collection by a planar electrode. The results show that there is some sensitivity of the relation to the type of gas and pressure, but the dependence of the relation on plasma density turns out to be slight. Therefore, the pressure parameterization of the relation for a certain gas can be used to establish plasma density by measuring ion current to an electrode and vice versa.
30 August 2022 in Plasma Sources Science and Technology
One of the crucial challenges facing modern microelectronics is to provide plasma surface treatment at the single atomic level. To minimize defects in the underlying layers, these processes require ions with very low energies—lower than in conventional radio-frequency (rf) plasma and close to the binding energy of atoms. A conventional rf dual-frequency capacitively coupled plasma (df CCP) discharge with additional ionization by an electron beam is considered as a possible solution to this problem. This paper contains a study on the electron beam effect on 81 & 12 MHz plasma parameters such as electron energy probability function, plasma density, electron temperature and ion energy distribution at an rf-biased electrode. The experimental part of the study includes measurements carried out in an asymmetric rf df CCP discharge in Ar at 100 mTorr pressure using a Langmuir probe, a hairpin-probe, and a retarding field energy analyzer. The behavior of plasma parameters is considered in the different types of plasma: electron beam plasma, when no rf power is applied, as well as rf plasma with and without an electron beam. The 1D PIC MCC simulation is used to analyze the effect of an electron beam on the df rf plasma. The obtained results showed that the electron temperature and, accordingly, the energy of ions coming at the electrode surface can be lowered. The use of an electron beam in a df CCP discharge allows to control the plasma density, electron temperature and ion energy spectrum in the low-energy range, which can be of essential interest for atomic layer etching and atomic layer deposition technologies.
1 September 2019 in Plasma Sources Science and Technology
The ion composition of Ar/H 2 plasmas along with the fluxes and energies of the certain ion sort are of great interest for various applications. In this paper the question of the main reactions which contribute most to the ion composition is being studied in an asymmetric dual-frequency rf CCP discharge with an applied rf-bias. A combination of experiment with a numerical scheme developed on the base of the particle-in-cell model with Monte-Carlo collisions is applied. The mass-spectrometer is used for measuring the ion composition at the discharge chamber wall, while the ion composition on the surface of an rf-biased electrode is estimated from the retarded field energy analyzer measurements to establish the role of the sheath processes in the ion composition. It is shown that the main ions are H 3 + , Ar + and ArH + but their relative concentrations strongly depend on the initial H 2 content in the mixture. The processes in the bulk plasma are revealed to be determinative for the ion composition whereas the sheath processes do not have a significant effect under the conditions considered.
23 May 2022 in Journal of Physics D: Applied Physics
Radio-frequency (rf) plasma with additional ionization by an electron beam (EB) is considered as a possible method for the independent control of plasma density, mean electron energy and mean ion energy. In this study, spatial transition from EB to rf-power-controlled dual-frequency capacitively coupled plasma (DFCCP) was studied using the following movable diagnostics: Langmuir and hairpin probes, a retarding field energy analyzer and optical emission spectroscopy. The beam (1.1–1.4 keV) is generated by a runaway EB module placed near the plasma chamber wall, while the plasma transition is caused by EB degradation with the distance from the EB module. The study was conducted in Ar at 200 and 400 mTorr gas pressures in 81 and 12 MHz DFCCP. When the EB is on, a significant decrease in the mean electron energy is observed, from 6 eV in the rf plasma down to 0.2–0.8 eV in the EB plasma. The EB also changes the shape of the electron energy probability function, from Druyvesteyn-like in rf plasma to Maxwellian-like. When both EB and rf power are applied, the mean electron energy increase and the electron density decrease, with the distance from the EB module, are observed due to the beam degradation. The ion energy distribution at the bottom electrode in rf plasma peaks at 25–30 eV and shifts down to a few eV in EB plasma. As in conventional DFCCP, the ion energy distribution can be fine-tuned by the application of a low-frequency rf bias. However, the use of an EB allows us to reduce the range of ion energies down to a few eV, which cannot be achieved in conventional rf discharges.