10 April 2025 in Plasma Physics and Controlled Fusion
TTthe EUROfusion Tokamak Exploitation Team
the EUROfusion Tokamak Exploitation Team
+65
JET returned to deuterium-tritium operations in 2023 (DTE3 campaign), approximately two years after DTE2. DTE3 was designed as an extension of JET’s 2022-2023 deuterium campaigns, which focused on developing scenarios for ITER and DEMO, integrating in-depth physics understanding and control schemes. These scenarios were evaluated with mixed D-T fuel, using the only remaining tritium-capable tokamak until its closure in 2023. A core-edge-SOL integrated H-mode scenario was developed and tested in D-T, showing good confinement and partial divertor detachment with Ne-seeding. Stationary pulses with good performance, no tungsten accumulation, and even without ELMs were achieved in D-T. Plasmas with pedestals limited by peeling modes were studied with D, T-rich, and D-T fuel, revealing a positive correlation between pedestal electron pressure and pedestal electron density. The Quasi-Continuous Exhaust regime was successfully achieved with D-T fuel, with access criteria similar to those in D plasmas. A scenario with full detachment, the X-point radiator regime, was established in D-T, aided by the real-time control of the radiator’s position. The crucial characterisation of tritium retention continued in DTE3, using gas balance measurements and the new LID-QMS diagnostic. Nuclear technology studies were advanced during the DTE3 campaign, addressing issues such as the activation of water in cooling loops and single event effects on electronics. Building on the previous D, T and DTE2 campaigns and the lessons learned from them, DTE3 extended our understanding of D-T plasmas, particularly in scenarios relevant to next-generation devices such as ITER and DEMO.
12 October 2023 in Nuclear Fusion
JET experiments using the fuel mixture envisaged for fusion power plants, deuterium and tritium (D–T), provide a unique opportunity to validate existing D–T fusion power prediction capabilities in support of future device design and operation preparation. The 2021 JET D–T experimental campaign has achieved D–T fusion powers sustained over 5 s in ITER-relevant conditions i.e. operation with the baseline or hybrid scenario in the full metallic wall. In preparation of the 2021 JET D–T experimental campaign, extensive D–T predictive modelling was carried out with several assumptions based on D discharges. To improve the validity of ITER D–T predictive modelling in the future, it is important to use the input data measured from 2021 JET D–T discharges in the present core predictive modelling, and to specify the accuracy of the D–T fusion power prediction in comparison with the experiments. This paper reports on the validation of the core integrated modelling with TRANSP, JINTRAC, and ETS coupled with a quasilinear turbulent transport model (Trapped Gyro Landau Fluid or QualLiKiz) against the measured data in 2021 JET D–T discharges. Detailed simulation settings and the heating and transport models used are described. The D–T fusion power calculated with the interpretive TRANSP runs for 38 D–T discharges (12 baseline and 26 hybrid discharges) reproduced the measured values within 20 . This indicates the additional uncertainties, that could result from the measurement error bars in kinetic profiles, impurity contents and neutron rates, and also from the beam-thermal fusion reaction modelling, are less than in total. The good statistical agreement confirms that we have the capability to accurately calculate the D–T fusion power if correct kinetic profiles are predicted, and indicates that any larger deviation of the D–T fusion power prediction from the measured fusion power could be attributed to the deviation of the predicted kinetic profiles from the measured kinetic profiles in these plasma scenarios. Without any posterior adjustment of the simulation settings, the ratio of predicted D–T fusion power to the measured fusion power was found as 65%–96% for the D–T baseline and 81%–97% for D–T hybrid discharge. Possible reasons for the lower D–T prediction are discussed and future works to improve the fusion power prediction capability are suggested. The D–T predictive modelling results have also been compared to the predictive modelling of the counterpart D discharges, where the key engineering parameters are similar. Features in the predicted kinetic profiles of D–T discharges such as underprediction ofneare also found in the prediction results of the counterpart D discharges, and it leads to similar levels of the normalized neutron rate prediction between the modelling results of D–T and the counterpart D discharges. This implies that the credibility of D–T fusion power prediction could bea prioriestimated by the prediction quality of the preparatory D discharges, which will be attempted before actual D–T experiments.
12 October 2023 in Nuclear Fusion
For more than a decade, an unprecedented predict-first activity has been carried in order to predict the fusion power and provide guidance to the second Deuterium–Tritium (D–T) campaign performed at JET in 2021 (DTE2). Such an activity has provided a framework for a broad model validation and development towards the D–T operation. It is shown that it is necessary to go beyond projections using scaling laws in order to obtain detailed physics based predictions. Furthermore, mixing different modelling complexity and promoting an extended interplay between modelling and experiment are essential towards reliable predictions of D–T plasmas. The fusion power obtained in this predict-first activity is in broad agreement with the one finally measured in DTE2. Implications for the prediction of fusion power in future devices, such as ITER, are discussed.
26 June 2025 in Plasma Physics and Controlled Fusion
The development of a high current baseline scenario ( , , ) in deuterium (D), tritium (T) and deuterium–tritium (D–T) for high D–T fusion performance at JET with Be/W wall is described. We show that a suitable scenario capable of delivering up to 10 MW of fusion power, depending on the auxiliary heating power available, was successfully developed in D. However, when translated to T and D–T, the same scenario could not be sustained for the target duration of 5 s due to the impossibility to achieve the stationary compound edge localized modes regime necessary to flush the tungsten (W) from the plasma and control the density. Nevertheless, a peak fusion power in the order of 8 MW, with 60% of the power coming from thermal fusion reactions, was obtained in D–T at 3.5 MA, with MW of neutral beam injection heating and 3–4 MW of ion cyclotron resonance heating, in line with the predictions obtained with the JINTRAC integrated scenario modelling suite of codes equipped with the QuaLiKiZ transport model and based on the extrapolation of the performance of similar D plasmas.
11 May 2022 in Nuclear Fusion
The fusion performance of ELMy H-mode 50–50 deuterium–tritium (DT) plasmas with 50–50 DT NBI injection and q 95 ≈ 3 and β N ≈ 1.8 (also referred to as medium-β N baseline scenario in the rest of this paper) are predicted with the JINTRAC suite of codes and the QuaLiKiZ transport model. The predictions are based on the analysis of plasmas from the first DT campaign on JET in 1997 (DTE1) and pure deuterium plasmas developed at JET in preparation for the DT experimental campaign in 2021 (DTE2), after the installation of a Be/W ITER-like wall in 2011. The sensitivity of the predictions to plasma parameters such as current, toroidal field, pedestal confinement and impurity content are analysed together with the sensitivity to the amount of auxiliary heating power available. The simulations indicate that a fusion power of 10 MW should be achievable under a fairly wide range of assumptions, provided that the auxiliary heating power is around or above 38 MW. Higher fusion power approaching 15 MW could be achievable for this value of β N only for particularly pure plasmas and with 40 MW of additional heating power.
11 July 2023 in Nuclear Fusion
We present the JETTO-QuaLiKiz-SANCO fully predictive modelling of two JET-ILW high-performance baseline plasmas, a Ne seeded shot and an equivalent unseeded one. The motivation of the work lies in the experimental observation of a slightly higher confinement and performance of the Ne seeded shot with respect to the unseeded one, despite sharing the same main plasma parameters and heating powers. Moreover, the neon seeded shot shows a lower pedestal electron density and a higher core ion temperature with respect to the unseeded one. Integrated modelling is performed in order to understand if the cause of the improved confinement has to be ascribed to the improved pedestal parameters with neon seeding or if an impurity-induced turbulence stabilization is at play. The QuaLiKiz transport model is used for predicting the electron density, electron and ion temperatures and rotation in the core up to the pedestal top, while the pedestal is empirically modelled to reproduce the experimental kinetic profiles. The thermal diffusivities of the two shots, computed by QuaLiKiz, are compared, as well as the turbulence spectra, suggesting that the reduced transport found in the neon seeded shot is due in part to the stabilization of ion temperature gradient and electron temperature gradient modes. Further modelling is performed in order to disentangle the neon seeding effects, which are a direct effect on the turbulence stabilization and an indirect effect on the pedestal parameters. The results suggest that the improved performance with neon is due to a combination of turbulence stabilization and improved pedestal parameters.