27 October 2021 in Advanced Energy and Sustainability Research
Poly(ethylene oxide) (PEO) was the first lithium‐ion conducting polymer developed 50 years ago and is still the most popular electrolyte matrix for solid‐state lithium metal batteries. While many studies focus on increasing PEO ionic conductivity through doping with Li salts, little work has addressed using PEO and Li directly to generate Li+‐conducting species in situ. Reaction between PEO and Li leads to ionic conductivity largely from Li+, in contrast to the case of added salts where the anion contribution dominates. Herein, electrochemical impedance spectroscopy shows the ionic conductivity of PEO thin films increases up to three orders of magnitude (from 10−7 to 10−4 S cm−1) when contacted with Li at elevated temperature. This is due to the reduction of ether bonds, which produces lithium alkoxides that are responsible for Li+ transport. Density functional theory analysis confirms this mechanism as thermodynamically favorable. X‐ray photoelectron spectroscopy also shows the presence of organolithium species and Li2O, which are responsible for propagating reactions with PEO and forming an electronically insulating layer at the PEO–Li interface that halts further reaction, respectively. The underlying mechanisms of Li–polymer electrolyte reactions is clarified and new pathways for in situ Li+ doping of polymer electrolytes is presented.
2 February 2018 in Analytical Chemistry
19 May 2023 in ACS Applied Materials & Interfaces
Composite polymer electrolytes (CPEs) are attractive materials for solid-state lithium metal batteries, owing to their high ionic conductivity from ceramic ionic conductors and flexibility from polymer components. As with all lithium metal batteries, however, CPEs face the challenge of dendrite formation and propagation. Not only does this lower the critical current density (CCD) before cell shorting, but the uncontrolled growth of lithium deposits may limit Coulombic efficiency (CE) by creating dead lithium. Here, we present a fundamental study on how the ceramic components of CPEs influence these characteristics. CPE membranes based on poly(ethylene oxide) and lithium bis(trifluoromethanesulfonyl)imide (PEO-LiTFSI) with Li7La3Zr2O12 (LLZO) nanofibers were fabricated with industrially relevant roll-to-roll manufacturing techniques. Galvanostatic cycling with lithium symmetric cells shows that the CCD can be tripled by including 50 wt % LLZO, but half-cell cycling reveals that this comes at the cost of CE. Varying the LLZO loading shows that even a small amount of LLZO drastically lowers the CE, from 88% at 0 wt % LLZO to 77% at just 2 wt % LLZO. Mesoscale modeling reveals that the increase in CCD cannot be explained by an increase in the macroscopic or microscopic stiffness of the electrolyte; only the microstructure of the LLZO nanofibers in the PEO-LiTFSI matrix slows dendrite growth by presenting physical barriers that the dendrites must push or grow around. This tortuous lithium growth mechanism around the LLZO is corroborated with mass spectrometry imaging. This work highlights important elements to consider in the design of CPEs for high-efficiency lithium metal batteries.
7 March 2022 in Journal of Materials Chemistry A
Irreparable chemical damage to redox-active monomers, oligomers, and polymers (i.e. redoxmers) limits the lifetime of energy storage devices (e.g. redox flow batteries) by causing electrode and membrane fouling, as well as irreversible capacity loss. To predictably restore device and materials performance, it is desirable to add programmed destruction capabilities into these damage-prone materials. Here, we report the use of triggerable retrograde reactions to achieve programmable end-of-life function in redoxmers. Retrograde reactions are intended to break up damaged redoxmer materials into more soluble small-molecule constituents to prevent irreparably fouling battery interfaces. We investigated the redox-triggered mesolytic cleavage of homobenzylic ethers (HBEs) for this purpose. Combining experimental methods with simulations, we probed the influence of ring substituents on the programmable bond-scission behavior of HBEs. Variation of para-substituents on the HBEs allowed us to modify the oxidation potential, degradation pathway, and electrochemical mechanisms of the generated products. Given its ideal oxidation potential, we selected the para-methoxy-based HBE as the cleavage scaffold and integrated it with dialkoxybenzene, TEMPO, viologen, and para-nitrobenzene redox centers for compatibility, bulk deconstruction, and electrode defouling tests. Upon applying a high oxidation potential, the redox-active pendant is cleaved from the backbone via HBE bonds; of the four redox centers tested, three of them remained fully redox active. Viologen-appended redox active polymers with HBE linkers were cleaved to fully separate the redox centers from the backbone. Polymer-filmed electrodes were partially restored following HBE oxidation defouling. These studies highlight the co-design of new materials functions for developing sustainable energy storage materials.
16 March 2023 in Chemical Communications
We synthesized Li and Na monocarborate salts with minimal protic impurities and reassessed their electrochemical windows. Na salts display higher efficiency for metal deposition/stripping and are more oxidatively stable than Li salts. This strong cation effect is rationalized in terms of differences in charge density between Li+ and Na+ cations.