23 December 2020 in IEEE Transactions on Aerospace and Electronic Systems
In this article, a finite-time control scheme is proposed for a quadrotor unmanned aerial vehicle (UAV) with external disturbance. First, a finite-time disturbance observer is designed to cope with external disturbance. Then, a nonsingular terminal sliding-mode control scheme is developed, which avoids singularity problem of conventional terminal sliding-mode control. By Lyapunov stability theory, it is proved that the controller guarantees the tracking errors converge to zero in a finite time. Finally, the effectiveness and superiority of the proposed control strategy is verified by compared simulation.
12 August 2021 in IEEE Transactions on Aerospace and Electronic Systems
This article addresses the tracking control problem of a hypersonic vehicle subject to multisource uncertainty and actuator fault. A composite fixed time control scheme is designed to achieve the stable tracking of velocity and altitude in fixed time. A nonsingular fast terminal sliding mode controller and a practically fixed-time backstepping controller are, respectively, developed for velocity subsystem and altitude subsystem. Fixed-time disturbance observer is used to tackle lumped uncertainties and a new fast fixed time filter is constructed to avoid the “explosion of terms” problem. Then, the fixed-time stability of velocity tracking error and the practically fixed-time stability of altitude tracking error are proved. Finally, compared simulations are carried out to present the efficiency of the designed control scheme.
11 May 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper considers the dynamic event-triggered consensus control design of leader-following multi-agent systems (MASs) under communication delay. Static event-triggered mechanism is often used, but its energy saving is limited. The dynamic event-triggered mechanism based on sampled data can obtain fewer trigger times than static event-triggered mechanism by adding a dynamic variable, which means that energy is saved to a greater extent and Zeno behaviors can be excluded obviously. Different from the existing works, this paper considers time-varying communication delay between agents. A periodic switching controller is used to deal with delay. Besides, the Lyapunov-Krasovskii function is applied to prove the stability of the closed-loop system and linear matrix inequality plays an important role in this process. Finally, simulation results illustrate the availability of the proposed controller.
23 January 2025 in IEEE Transactions on Systems, Man, and Cybernetics: Systems
This article investigates the practical fixed-time optimal consensus problem for multiagent systems (MASs). Under the detailed balanced digraph, a controller with tangent function is constructed so that the MASs can reach consensus within a fixed time and then gradually converges to the global optimal solution on the basis of reaching stability. Besides, an important lemma about hyperbolic tangent function is derived to contribute to the stability analysis. In the process, an adaptive dynamic event-triggered mechanism (ADETM), including anti-cotangent function, is constructed to achieve the number of controller updates is significantly reduced. Eventually, the validity of the consensus control method proposed in this article is verified by a numerical simulation and a power system simulation.
31 March 2020 in Complexity
Nonsinusoidal oscillation techniques can shorten the negative strip time and improve the slab surface quality in the process of steel continuous casting. But the acceleration of nonsinusoidal oscillation is higher than that of the sinusoidal oscillation. So it is easy to result in the impact for the mold movement. To solve this problem, a nonsinusoidal oscillation waveform function of mold was constructed, which had good dynamic characteristics. And the smaller acceleration can reduce the impact of the oscillator. By analyzing the parameters of oscillation technology, the calculation method of each oscillation technological parameter for seven section functions was presented and the multitechnological parameter curves were given. Based on the technological parameters of sinusoidal oscillation, a synchronous control model of nonsinusoidal oscillation was determined. The results show that the parameters can satisfy the limit value in theory, which can enhance the casting speed, surface quality of slab, and provide reference for further practice in industry.
6 December 2019 in IEEE Access
To improve the surface quality and casting speed of the slab further, a new type mold oscillator synchronously driven by double servomotors was proposed in this paper. The experimental prototype was designed and manufactured. For the non-sinusoidal oscillator, the waveform modification ratio could be adjusted during the steel continuous casing operation. Firstly, the working principle of the oscillator was described. Secondly, the rotating rules of the servomotor to realize non-sinusoidal oscillation waveform for entire function were given. Finally, the laboratory experiments were made. The experiment results show that the error of the two-side oscillation curves is smaller and the actual technological parameters are close to the theory and the oscillator can realize non-sinusoidal oscillation well. This kind of non-sinusoidal oscillator provides a feasible scheme for reducing oscillator investment, increasing casting speed and enhancing slab quality.