Benefiting from the high breakdown voltage of the silicon carbide (SiC) material, the medium voltage SiC power module has made an unprecedented breakthrough, which is regarded as a promising route for the high voltage converter. However, partial discharge (PD) challenges the reliability and safety of the medium voltage SiC power module, which limits its massive applications in industrial fields. In this article, insightful models are proposed to reveal the mechanism of the electric-field-dominated PD in the medium voltage power module. Furthermore, it is found that the distorted electric field at the triple point of the power packaging is caused by the edge effect. Besides, the low-cost equipotential ring concept and structure are proposed to dramatically decrease the distorted electric field at the triple point. Additionally, the experiment platform with ultra-low interferences is presented to assess and localize the PD. With the aid of the proposed test bench, the PD principles in conditions of different ceramic thicknesses, electrode distances, and copper lengths of the copper plates of the DBC are measured. Comparative experiments ensure the feasibility and effectiveness of the proposed equipotential ring structure, which can significantly decrease the PD issue and promote the isolation level of the medium voltage SiC power module.
21 August 2023 in IEEE Transactions on Power Electronics
Rogowski coil (RC) has been commonly employed in power electronics due to its benefits of galvanic isolation, high-current measurement capability, and simple integration. However, the bandwidth of RC is restricted to tens of MHz because of the inextricable resonance issue caused by its self-inductance and parasitic capacitance. This limitation hinders the ability of the RC to measure fast current transients such as those of wide-bandgap (WBG) power devices. In this letter, the concept of transmission line Rogowski coil (TL-RC) is proposed to address the limitations of inductance and capacitance. The design criteria of double-ended impedance matching are further derived to ensure optimal signal integrity of TL-RC at GHz levels. These two concepts jointly form the isolated current sensor design with a bandwidth exceeding 3 GHz. Comparative experiments confirm the ultrafast and isolated advantages of the TL-RC for the WBG applications.
23 May 2022 in IEEE Transactions on Power Electronics
The current shunt with high bandwidth and low parasitics is critically needed to satisfy the soaring current slew rate of the wide-bandgap (WBG) device. However, the existing lumped parameter model is inappropriate to model and design the next-generation ultrahigh bandwidth current shunt, leading to the unclear bandwidth limitation, inextricable invasive effect, and lacked design guidance. In this letter, by introducing the transmission line theory, it is revealed that, due to the impedance mismatch, the strong signal reflection inside the current shunt results in the high-frequency parasitic inductance, which severely deteriorates its bandwidth. On this basis, the concept of the impedance-matching shunt (IM-shunt) is then proposed to derive the mathematical model-guided design methodology for the high-performance current shunt. With the aid of the proposed concept, the current shunt with > 3 GHz bandwidth and < 0.1 nH parasitics is developed. The comparative experiments further ensure the accurate and nonintrusive characterization of the switching trajectories for the WBG application.
1 July 2025 in IEEE Transactions on Power Electronics
The increasing pursuit of high efficiency and power density in EV traction inverters is accelerating the deployment of the wide bandgap device, including silicon carbide (SiC) and gallium nitride (GaN). As the efficiency-density boundary of the SiC traction inverter has approached its limitation, the traction inverter utilizing GaN devices, with lower power loss and higher switching speed, is considered as a promising solution. Focusing on the GaN traction inverter for EV applications, this article proposes a design methodology considering the co-optimization of the pursued efficiency and power density objectives. Based on the created mathematical models of design concerns, including power loss, dc-link ripple, and thermal resistance, the efficiency-density design domain of the GaN inverter is established, upon which the optimal design space of the efficiency-density is determined through Pareto frontier analysis. Based on the co-optimization results, a 100 kW / 400 V GaN traction inverter prototype is compactly integrated, incorporating meticulously designed key components, including the GaN power module, dc-link capacitor, and heat sink. Experimental validation confirms the effectiveness of the proposed co-optimization methodology and demonstrates the feasibility of the integrated GaN inverter, achieving the high power density 62.1 kW/L and peak efficiency 99.3%.
26 January 2021 in IEEE Transactions on Power Electronics
Parasitic inductance reduction is increasingly vital for the SiC power module in high-frequency and high-capacity applications. To address the parasitic issue, the automatic layout design offers the potential to pursue the optimal configuration of the power packaging. However, the efficient and accurate parasitic extraction of the packaging is the bottleneck of the automatic design scenario. In this letter, the current-bunch concept is proposed to achieve a tradeoff between the efficiency and accuracy of the parasitic extraction. The mathematical models are created to estimate the parasitics by using the proposed concept. Additionally, the challenge of abundant mutual-inductance caused by the multiplied power chips in the SiC power module is highlighted. Simulation and experimental results further demonstrate the advantages of the current-bunch concept. With the aid of the proposed approach, the packaging layout of a multichip SiC power module is optimized, and the parasitic inductance is reduced by 29.2%.
15 February 2023 in IEEE Transactions on Device and Materials Reliability
Owing to the low parasitic inductance, high power density, and excellent heat extraction performance, double-sided cooling (DSC) is regarded as a promising packaging solution for the silicon carbide (SiC) power module. Nevertheless, given the unclear failure mechanism and missed lifetime model, the reliability assessment and lifetime prediction of the DSC SiC power module remains a concern. Besides, the accelerated aging test generally used for the reliability assessment of the SiC power module is extremely time-consuming and costly. Therefore, the obstacles mentioned before limit the development and deployment of the DSC SiC power module. Aiming to fulfill these research gaps, based on the aging mechanism and failure criterion of packaging materials, the lifetime model of the DSC SiC power module is proposed in this paper. Comparative experiments show that the relative error of the FEA-dominated model is less than 6%. Moreover, the stress property and creep principle of the solder layer in SiC and Si power modules are assessed, respectively. Besides, the lifetime models of SiC and Si power modules applying different packaging materials are created. It is found that the lifetime of the DSC power module is twice that of the single-sided cooling (SSC) counterpart. Furthermore, applying the same packaging, the lifetime of the SiC power module decreases by 70% compared with the Si counterpart. In addition, the lifetime of the DSC SiC power module affected by different materials such as ceramic and spacer is studied in order to enhance its reliability.