Daily temperature variations induce phase transitions and lattice strains in halide perovskites, challenging their stability in solar cells. We stabilized the perovskite black phase and improved solar cell performance using the ordered dipolar structure of β-poly(1,1-difluoroethylene) to control perovskite film crystallization and energy alignment. We demonstrated p-i-n perovskite solar cells with a record power conversion efficiency of 24.6% over 18 square millimeters and 23.1% over 1 square centimeter, which retained 96 and 88% of the efficiency after 1000 hours of 1-sun maximum power point tracking at 25° and 75°C, respectively. Devices under rapid thermal cycling between −60° and +80°C showed no sign of fatigue, demonstrating the impact of the ordered dipolar structure on the operational stability of perovskite solar cells.
6 July 2021 in Angewandte Chemie International Edition
Tin is the frontrunner for substituting toxic lead in perovskite solar cells. However, tin suffers the detrimental oxidation of SnII to SnIV. Most of reported strategies employ SnF2 in the perovskite precursor solution to prevent SnIV formation. Nevertheless, the working mechanism of this additive remains debated. To further elucidate it, we investigate the fluoride chemistry in tin halide perovskites by complementary analytical tools. NMR analysis of the precursor solution discloses a strong preferential affinity of fluoride anions for SnIV over SnII, selectively complexing it as SnF4. Hard X‐ray photoelectron spectroscopy on films shows the lower tendency of SnF4 than SnI4 to get included in the perovskite structure, hence preventing the inclusion of SnIV in the film. Finally, small‐angle X‐ray scattering reveals the strong influence of fluoride on the colloidal chemistry of precursor dispersions, directly affecting perovskite crystallization.
Tin-based perovskite solar cells offer a less toxic alternative to their lead-based counterparts. Despite their promising optoelectronic properties, their performances still lag behind, with the highest power conversion efficiencies reaching around 15%. This efficiency limitation arises primarily from electronic defects leading to self-p-doping and stereochemical activity of the Sn(II) ion, which distorts the atomic arrangement in the material. In this study, we investigate the effect of strontium doping in tin-based perovskite on the distortion of the material’s structure and its optoelectronic properties. Using a combination of Density Functional Theory calculations and experiments, we demonstrate that strontium doping reduces p-doping and structural strain. This approach improves the efficiency from 6.3% in undoped devices to 7.5% in doped devices without relying on dimethyl sulfoxide, a harmful solvent for tin-based perovskites. This method could enable precise control of tin off-centering and self-p-doping, advancing the development of efficient and stable tin perovskite solar cells.
17 August 2016 in Journal of Dispersion Science and Technology
Four copolymers were prepared by copolymerization of octadecyl acrylate with maleic anhydride abbreviated as [ODM], the resulted copolymer was reacted with octadecylalcohol [ODMSA], hexadecylamine [ODMCA], benzyl alcohol [ODMBA] and aniline [ODMAn]. Three oil-soluble surfactants were also prepared by esterification of mono, di and tri ethanolamine with oleic acid, abbreviated as [MEAO, DEAO and TEAO]. These compounds were purified and characterized by FTIR, 1H-NMR and GPC. The prepared copolymers were evaluated individually and mixed with the oil-soluble surfactants and evaluated as flow improvers and pour point depressants for waxy crude oil. It was found that, the polymer with aromatic side chain [ODMBA] exhibited the maximum pour point depression ΔPP = 24°C at concentration 1000 ppm, while the minimum pour point depression was obtained by [ODMCA] which pronounced ΔPP = 15°C at 1000 ppm. Furthermore, the blend [B4] between [ODMBA] and oil-soluble surfactant [TEAO] achieved extra depression of pour point (ΔPP = 30°C). The rheological properties of the treated and untreated crude oil with the polymeric additives were also investigated and it was found that Bingham yield value (τB) was decreased from 1.63 Pa at 32°C to 0.3 Pa at the same temperature and 500 ppm concentration of [ODMBA]. GRAPHICAL ABSTRACT