Karsten Behnke

Karsten Behnke

Auto-generated profile, based on publicly available information

Karsten Behnke

Fraunhofer Institute for Wind Energy Systems IWES, Am Schleusengraben 22, 21029, Hamburg, Germany

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 March 2023 in Wind Energy Science
Verified
Journal Article
Open access
PDF file
KBKarsten Behnke
Karsten Behnke
FSFlorian Schleich
Florian Schleich
Oscillating movements under load can cause wear in rolling bearings. Blade bearings of wind turbines are subject to both. To know how to avoid wear in these bearings is important since they ensure the operational safety of the turbine. Oscillations of blade bearings vary in load, speed, and amplitude. The objective of this work is to find limits of these operating parameters with regards to wear occurrence. To this end several tests with real-size bearings were carried out. The test parameters are based on typical operating conditions of a reference turbine. The size of the bearings and the test parameters differ from other published tests for oscillating bearings, where often scaled bearings are used results. The test results show that wear occurs for every tested combination of load, speed, and amplitude of a steady oscillating movement. Even if the wear characteristics differ between tests, each of them resulted in wear. Hence, no wear limits can be defined with the tested grease and within typical operating conditions of a wind turbine below which wear does not occur. Tests with a discontinuity in the steady oscillation movement, however, did not result in wear. Such discontinuities can be longer movements embedded in steady oscillations. They are characteristic to wind turbine operation, where longer movements are a reaction to wind gusts.

9 October 2023 in Wind Energy Science
Verified
Journal Article
Open access
PDF file
ABArne Bartschat
Arne Bartschat
KBKarsten Behnke
Karsten Behnke
MSMatthias Stammler
Matthias Stammler
The characteristics of a pitch controller determine how the wind turbine reacts to different wind conditions. Control strategies like individual pitch control are known for their ability to reduce the amplitudes of load cycles of the structures of the wind turbine while influencing the operation conditions of the blade bearings in a challenging way. However, the control strategy is not the only influencing factor with respect to failure modes of blade bearings like wear and raceway fatigue. The site-specific and stochastic wind conditions can cause wear-critical operating conditions, which are usually not reflected in the rather short time frames of aeroelastic simulations. This work analyses exemplary wind and operating conditions of one specific site regarding their influence on wear in blade bearings. It is based on measured wind conditions and the modeled behavior of the individual pitch-controlled IWT-7.5-164 reference wind turbine with respect to its pitch activity. The simulation data are used to determine the longest period of uninterrupted wear-critical operation and create a test program based on it for scaled and real-size blade bearings. Experimental results based on this test program show that wear-critical operation conditions can occur during normal operation of a wind turbine and cause mild wear damage to the bearing raceways.

5 November 2025 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Open access
KBKarsten Behnke
Karsten Behnke
OMOliver Menck
Oliver Menck
Blade bearings of wind turbines are grease-lubricated rolling bearings which are operated in an oscillating manner. They can be subjected to both rolling contact fatigue and wear, in particular standstill marks and false brinelling. Rolling contact fatigue arises from alternating stresses due to the passage of rolling elements under high loads, standstill marks and false brinelling occur during cyclic motion and are often exacerbated by inadequate lubrication. In this paper, we want to understand fatigue and the influence of false brinelling on fatigue better and to investigate whether it is advantageous to avoid false brinelling. We performed fatigue tests with four blade bearings. Three of them had existing false brinelling damage. In addition, we repeated tests on much smaller angular contact ball bearings. To contextualize the results, we calculated the fatigue life of a pitch bearing from a reference turbine matching our test bearing design and compared the calculation to the test results. Although the stochastic fatigue behavior in combination with the low number of tests makes it difficult to draw general conclusions, the results indicate that false brinelling shortens fatigue life, even if the blade bearings pass the fatigue test.

15 May 2023 in EGUsphere
Verified
Preprint
Open access
PDF file
ABArne Bartschat
Arne Bartschat
KBKarsten Behnke
Karsten Behnke
MSMatthias Stammler
Matthias Stammler
The characteristics of a pitch controller determine how the wind turbine reacts to different wind conditions. Control strategies like individual pitch control are known for their ability to reduce the amplitudes of load cycles of the structures of the wind turbine while influencing the operation conditions of the blade bearings in a challenging way. However, the control strategy is not the only influencing factor with respect to failure modes of blade bearings like wear and raceway fatigue. The site-specific and stochastic wind conditions can cause wear-critical operating conditions, which are usually not reflected in the rather short time frames of aeroelastic simulations. This work analyses wind and operating conditions regarding their influence on wear in blade bearings. It is based on measured wind conditions and the modelled behavior of the IWT-7.5-164 reference wind turbine with respect to its pitch activity. The simulation data is used to determine the longest period of uninterrupted wear-critical operation and create a test program based on it for scaled and real-size blade bearings. Experimental results based on this test program show that wear-critical operation conditions can occur during normal operating of a wind turbine and cause wear damage to the bearing raceways.

1 November 2022 in EGUsphere
Verified
Preprint
Open access
PDF file
KBKarsten Behnke
Karsten Behnke
FSFlorian Schleich
Florian Schleich
Oscillating movements under load can cause wear in rolling bearings. Blade bearings of wind turbines are subject to both. To know how to avoid wear in these bearings is important since they ensure the operational safety of the turbine. Oscillations of blade bearings vary in load, speed, and amplitude. The objective of this work is to find limits of these operating parameters with regards to wear occurrence. To this end several tests with real size bearings were carried out. The test parameters are based on typical operating conditions of a reference turbine. The size of the bearings and the test parameters differ from other published test results for oscillating bearings. The test results show that wear occurs for every tested combination of load, speed, and amplitude of a steady oscillating movement. Even if the wear characteristics differ between tests, each of them resulted in wear. Hence, no wear limits can be defined within typical operating conditions of a wind turbine below which wear does not occur. Tests with a discontinuity in the steady oscillation movement, however, did not result in wear. Such discontinuities can be longer movements embedded in steady oscillations. They are characteristic to wind turbine operation, where longer movements are a reaction to wind gusts.