1 October 2025 in IEEE Transactions on Microwave Theory and Techniques
This article presents RF and microwave power amplifiers (PAs) that utilize hetero-dielectric (HD) lumped elements in matching circuits. The proposed innovative model achieves a higher $Q$ -factor due to its unique electromagnetic (EM) properties compared with conventional on-chip (OC) lumped elements and microstrip circuits. For the first time, formulas for calculating the parameters of the equivalent lumped elements of the model are given. This HD lumped element with a high $Q$ -factor reduces the matching circuit loss and further improves the performance of the PA. The design of the PA based on an HD model has been theoretically explored and experimentally validated using 0.25- $\mu $ m GaN HEMTs microwave integrated circuits (MICs) at 2.8–3.6 GHz. The drain efficiency (DE) ranges from 53.6% to 63.2% at an output power of 33.5–35.3 dBm, and the adjacent channel leakage power ratios (ACLRs) are −38.1dBc. High $Q$ -factor passive elements based on this model are expected to play an important role in realizing OC low-insertion loss filters and high-efficiency PAs.
1 April 2025 in IEEE Transactions on Microwave Theory and Techniques
This article proposes the general phase-noise (PN) synthesis technique for negative-resistance (NR) oscillator (OSC) design. The proposed synthesis method of designing an OSC according to the required PN and various conditions will be useful to the OSC designers struggling with tradeoffs among electrical performance, cost, and size. Specifically, a new linear PN model that takes both the frequency stabilization network and the active device with series feedback into consideration is presented. The explicit relationship between PN and the filtering frequency-selective network (FFSN) is established. According to the proposed synthesis technique, the PN of an OSC can be prescribed before design, and then, the circuit can be extracted based on the given PN performance. Four different types of 4-GHz OSCs are designed based on the prescribed PN goals: −130 dBc/Hz at 1 MHz, −145 dBc/Hz at 1 MHz, −160 dBc/Hz at 1 MHz, and −130 dBc/Hz at 10 kHz. The design results of these four OSCs meet the target specifications and match well with the theoretical PN curves, demonstrating the proposed synthesis technique. In addition, the measured figure of merit (FOM) of the novel second-order SIW OSC at 4 GHz is −213.72 dBc/Hz at 100 kHz and −216 dBc/Hz at 1 MHz, showing the state-of-the-art performance among all the reported planar OSCs.
29 January 2025 in IEEE Transactions on Microwave Theory and Techniques
In this article, compact tunable filter and filtering power divider (FPD) with multilevel transfer function tunability based on dual-mode dielectric resonators (DRs) are presented. Two metallic screw pairs (SPs) are arranged on the DR puck, allowing for flexible control of frequencies of the resonant modes and their couplings. Thus, filtering devices with multilevel transfer function tunability can be realized. In addition, the DR puck can switch between single-and dual-mode operations, which is suitable for designing band-switchable filtering devices. Characteristics of the dual-mode DR and control mechanisms are provided in detail. Furthermore, several RF filtering devices are explored to validate the proposed structure: 1) filter with band-switchable capability; 2) filter with self-equalized and elliptic function reconfiguration capability; 3) filter with reconfigurable asymmetric transmission zeros (TZs); and 4) band-switchable FPDs with common-mode (CM) suppression. Good agreement between simulation responses and measured results validates the proposed design concept. Regardless of the reconfiguration transfer function ability, all devices can be center frequency (CF) tuned.
15 May 2025 in IEEE Transactions on Microwave Theory and Techniques
This article proposes a new class of monoblock dielectric stub-loaded resonators (MDSLRs) to realize highly selective single- and dual-band filters. The proposed MDSLR can be chosen flexibly for both single- and dual-mode operations, enabling the design of single- and dual-band filters. For single-band filter design, frequency-dependent coupling (FDC) can be generated easily in a strictly inline configuration. Thus, a series of transmission zeros (TZs) are introduced and can be precisely controlled to enhance the selectivity. For dual-band filter design, the MDSLR offers independent control for two passbands with good selectivity and isolation. Moreover, a mixed input/output coupling structure is presented, effectively improving the tuning range of external quality factors ( $Q_{e}$ ). To demonstrate the above design concept, an inline fourth-order single-band filter and an inline fourth-order dual-band filter are designed and manufactured. Measurement results agree with the full-wave simulation ones.
1 September 2026 in IEEE Transactions on Microwave Theory and Techniques
9 March 2026 in IEEE Access
This paper introduces a novel and generalized synthesis approach for realizing highly selective filtering amplifiers (FAs) based on a new type of Extracted-Pole Matching Filter (EPMF). Conventional FA designs often face significant trade-offs between high-order filter selectivity, integration compactness, and synthesis complexity, particularly when realizing non-bandpass responses. The proposed EPMF technique addresses these challenges by exploiting the inherent merits of the Extracted-Pole (EP) topology, which readily provides multiple, precisely controllable transmission zeros (TZs) within a compact, inline configuration. This allows the EPMF to serve as a matching network (MN) that simultaneously absorbs frequency-dependent complex impedances (from source ZS to load ZL) while shaping highly selective quasi-elliptic low-pass (LP), high-pass (HP), and band-pass (BP) filter responses. The comprehensive MF synthesis formulas are derived to facilitate the semi-analytical design. For verification, three linear amplifiers are impedance-matched using the proposed LP-/HP-/BP-EPMFs and fabricated as demonstrative single-stage Extracted-Pole FA (EPFAs). Experimental results confirm that these FAs successfully achieve stringent, high-order responses, specifically 4-pole/4-TZ for LP and HP, and 6-pole/4-TZ for BP prototypes. Notably, the measured LP-EPFA achieves an exceptional stopband rejection up to 3.33fcen (11 GHz), and the BP-EPFA maintains rejection up to 4.3fcen. This work validates that the EPMF technique offers superior selectivity and design versatility compared to existing multi-stage solutions.