Yusuf Arman

Yusuf Arman

Auto-generated profile, based on publicly available information

Yusuf Arman

Faculty of Engineering Department of Mechanical Engineering Dokuz Eylul University Izmir Turkey

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 July 2024 in Polymers for Advanced Technologies
Verified
Journal Article
Open access
NPNihal Puhurcuoğlu
Nihal Puhurcuoğlu
YAYusuf Arman
Yusuf Arman
This study focused on determining the curing kinetic parameters of amine‐epoxy resin by performing dynamic DSC tests. The Kissinger and Crane equations were used to determine the activation energy, the pre‐exponential factor, and the reaction order as kinetic parameters for curing. The Ozawa equation was also used to determine the activation energy that changes at different levels of cure during the reaction. The average activation energy obtained by the Ozawa method was compared with the Kissinger activation energy. In addition, the T‐β extrapolation method was used to determine the optimum curing temperature. The kinetic parameters obtained from the Kissinger and Crane equations were used in the nth‐order kinetic model to predict the degree of cure at a given time and temperature. The linear regression fitting method was used in Minitab software to determine the curing parameters. The results were evaluated based on the fitting parameters. This study provides a theoretical basis for the curing mechanisms of epoxy matrix fiber composites used in the manufacture of wind turbine blades.

21 February 2018 in Mechanics
Verified
Journal Article
Open access
PDF file
ADAkar Doğan
Akar Doğan
YAYusuf Arman
Yusuf Arman
The present paper examines the effects of hygrothermal aging on the reinforced epoxy composites. The roles of reinforcement types and stacking sequence on the mechanical properties of composites under hygrothermal aging are investigated. Four different composite materials with different stacking sequence were produced. Unidirectional E-glass and carbon fabrics with an areal density 300 gr/m2 as reinforcement and epoxy as matrix were used. Composites were manufactured using vacuum-assisted resin infusion molding. In order to determine the mechanical properties of the composites, specimens were prepared according to the ASTM standards. The aging process was carried out in climatic test cabin at a temperature of 90 oC and a humidity of 90%. As a result of the tests, while the tensile strength of the glass reinforced composites decreased with aging time, no significant change was observed for carbon and hybrid composites. On the other hand, the tensile strength decreased in transverse direction for all types of composites. XPS analysis was used to understand the distribution of atoms on the surface of specimens. DOI: http://dx.doi.org/10.5755/j01.mech.24.1.18508

1 March 2009 in Composites Part B: Engineering
Verified
Journal Article
Closed access
EEErsin Eryiğit
Ersin Eryiğit
MZMehmet Zor
Mehmet Zor
YAYusuf Arman
Yusuf Arman

4 April 2020 in Journal of Composite Materials
Verified
Journal Article
Closed access
PDF file
ATA Kaan Toksoy
A Kaan Toksoy
VAVolkan Arıkan
Volkan Arıkan
RKRamazan Karakuzu
Ramazan Karakuzu
YAYusuf Arman
Yusuf Arman
Aytaç GörenAytaç Gören
Aytaç Gören
Spall behavior of single and multi-layered hybrid composite structures behind armor was investigated by using shaped charge. Firstly, spall cone angles of Aluminum 5083-H116 and rolled homogeneous armor (RHA) steel as base armor materials were determined without any composite to select base armor. The single and multi-plates composite samples were produced by using S2 glass plain fabric, Kevlar plain fabric and hybrid Carbon-Kevlar twill fabric and epoxy resin system. After that, composite samples were placed behind the selected base armor plates with different distance in between them. The changes of spall cone angle, spall diameter, and penetrated area after shaped charge penetration were determined and analyzed in terms of both material configuration and distance behind the armor plates. As a result, increasing the behind armor distance reduces the jetting area and thus spall distribution decreases. In addition, it can be recommended to use hybrid 1 and 50 mm behind armor distance by evaluating both spall distribution and in-vehicle volume restriction.

10 July 2012 in Journal of Composite Materials
Verified
Journal Article
Closed access
MTM Evren Toygar
M Evren Toygar
ZKZeki Kıral
Zeki Kıral
OSOnur Sayman
Onur Sayman
YAYusuf Arman
Yusuf Arman
MOMustafa Ozen
Mustafa Ozen
The aim of this study is investigation of the effect of interface crack on lateral buckling load and free vibration response of a sandwich composite beam using experimental methods and finite element solutions. The lateral buckling load and natural frequencies in a thin sandwich composite cantilever beam with crack were considered. The crack was opened between the face sheets and foam core. The length of the crack was selected, such as 100, 150, 200, and 250 mm. Lateral buckling and vibration tests were applied on these samples and then the critical lateral buckling load and natural frequencies were found using experimental and finite element method. In the experimental studies, in-house test mechanisms were used. For the numerical analysis, ANSYS finite element software was used. Close results were obtained between both two methods.

1 September 2009 in Journal of Biomechanics
Verified
Journal Article
Closed access
YAYusuf Arman
Yusuf Arman
MZMehmet Zor
Mehmet Zor
MGM. Ali Güngör
M. Ali Güngör
EAEnder Akan
Ender Akan
SASami Aksoy
Sami Aksoy