7 June 2019 in Nuclear Fusion
6 September 2019 in Nuclear Fusion
Core density profile peaking and electron particle transport have been extensively studied by
performing several dimensionless collisionality (υ*) scans with matched other dimensionless profiles in
various plasma operation scenarios on JET. This is the first time when electron particle transport coefficients
in H-mode have been measured on JET with high resolution diagnostics and thus, we are in a
position to distinguish between the NBI source and inward electron particle pinch in contributing to core
density peaking. The NBI particle source is found to contribute typically 50-60% to the electron density
peaking in JET H-mode plasmas where Te/Ti~1 or smaller and at υ*=0.1-0.5 (averaged between r/a=0.3-
0.8), and being independent of υ* within that range. In these H-mode plasmas, the electron particle
transport coefficients, De and ve, are small, thus giving rise to the large influence of NBI fueling with
respect to transport effect on peaking. In L-mode plasma conditions, the role of the NBI source is small,
typically 10-20%, and the electron particle transport coefficients are large. These dimensionless υ* scans
give the best possible data for model validation. TGLF simulations are in good agreement with the
experimental results with respect to the role of NBI particle source versus inward pinch in affecting
density peaking, both for the H-mode and L-mode υ* scans. It predicts similarly to experimental results
that typically roughly half of the peaking is originating from the NBI fuelling in H-mode and 10-20%
in L-mode. GENE simulation results also support the key role of NBI fuelling in causing peaked density
profile in JET H-mode plasma (Te/Ti~1 and υ*=0.1-0.5) and in fact, give even higher weight on NBI
fuelling than experimentally observed or predicted by TGLF. For the non-fuelled H-mode plasma at
higher Te/Ti=1.5 and lower βN and υ*, both TGLF and GENE predict peaked density profiles, therefore
agreeing well with experimental steady-state density peaking. Overall, the various modelling results
give a fairly good confidence in using TGLF and GENE in predicting density peaking in quite a wide
range of plasma conditions in JET.
12 May 2020 in Nuclear Fusion
17 January 2024 in Plasma Physics and Controlled Fusion
TTthe EUROfusion tokamak exploitation team
the EUROfusion tokamak exploitation team
+17
Under the auspices of EUROfusion, the ITER baseline (IBL) scenario has been jointly investigated on AUG and TCV in the past years and this paper reports on the developments on TCV. Three ITER shapes, namely the JET, AUG and ITER IBL have been reproduced in TCV, illustrating that the higher the triangularity the larger the ELM perturbation and the more difficult it is to reach stationary states with q 95< 3.6. It is found that the performance of TCV IBL is mainly limited by (neoclassical) tearing modes, in particular 2/1 modes which are triggered after a large ELM. It is demonstrated that the shorter the ELM period the larger β
N
at the NTM onset. We show that these modes can be avoided with central X3 EC heating at relatively high q 95 and moderate β
N
. However, the lack of significant ECH at the high central densities obtained in TCV IBL scenario limits the duration of low q 95 cases to about four confinement times. During this time, density usually keeps peaking until (neoclassical) tearing modes are triggered. Nevertheless, the TCV IBL database covers the ITER target values ( 1, 1.8 at 3) and a slightly better confinement than requested for ITER is reported. Integrated modelling results show that ITG modes are the dominant instabilities, and show that, in TCV, fuelling also plays a role to sustain peaked density profiles. The role of profiles, sawteeth and ELMs regarding MHD stability are also discussed.
10 October 2024 in Nuclear Fusion
Designing a robust termination scenario for a burning ITER plasma is a challenge that requires extensive core plasma and divertor modelling. The presented work consists of coupled core/edge/SOL/divertor simulations, performed with the JINTRAC code, to study the Q = 10 flat-top phase and exit phase of the ITER 15 MA/5.3 T DT scenario. The modelling utilizes the recently implemented option to treat deuterium and tritium separately in the SOL/divertor, enabling a consistent treatment of deuterium and tritium in the whole plasma volume, which is a unique capability of JINTRAC. In addition, these are the first JINTRAC simulations of this scenario that use a first-principles transport model to self-consistently model the ECRH power deposition and to include tungsten while keeping track of tungsten sputtering and accumulation. The flat-top simulations demonstrate the possibility of sustaining a steady state fusion Q of 10 using pure deuterium gas puffs together with DT mixed pellets, which is an option to make a more effective use of tritium. Simulations of the exit phase are set up sequentially, with each phase providing initial conditions for the next, starting with a density decay at full current and auxiliary power, and demonstrate the possibility of reducing the density robustly within a few seconds. Following the density decay, a subsequent auxiliary power ramp-down in H-mode is performed with a late H–L transition at low auxiliary power, which may provide an option for the optimization of the plasma termination. The final ramp-down phase consists of a current ramp-down in L-mode to 3.75 MA.
30 March 2022 in Nuclear Fusion
Density peaking has been studied between an ICRH and NBI identity plasma in JET. The comparison shows that 8 MW of NBI heating/fueling increases the density peaking by a factor of two, being R/L n = 0.45 for the ICRH pulse and R/L n = 0.93 for the NBI one averaged radially over ρ tor = 0.4, 0.8. The dimensionless profiles of q, ρ *, υ *, β n and T i/T e ≈ 1 were matched within 5% difference except in the central part of the plasma (ρ tor < 0.3). The difference in the curvature pinch (same q-profile) and thermo-pinch (T i = T e) between the ICRH and NBI discharges is virtually zero. Both the gyro-kinetic simulations and integrated modelling strongly support the experimental result where the NBI fuelling is the main contributor to the density peaking for this identity pair. It is to be noted here that the integrated modeling does not reproduce the measured electron density profiles, but approximately reproduces the difference in the density profiles between the ICRH and NBI discharge. Based on these modelling results and the analyses, the differences between the two pulses in impurities, fast ions (FIs), toroidal rotation and radiation do not cause any such changes in the background transport that would invalidate the experimental result where the NBI fuelling is the main contributor to the density peaking. This result of R/L n increasing by a factor of 2 per 8 MW of NBI power is valid for the ion temperature gradient dominated low power H-mode plasmas. However, some of the physics processes influencing particle transport, like rotation, turbulence and FI content scale with power, and therefore, the simple scaling on the role of the NBI fuelling in JET is not necessarily the same under higher power conditions or in larger devices.