With development of electrical machines, traditional machine theory can no longer explain the operation principles of some new type machines, such as vernier machine, stator PM machine, etc. The principle of flux-modulation (FM) provides an important direction for development of machine theory. This study overviews the development of the FM machine regarding its principle and topology. According to the studies on FM effect of different types of electrical machines, it can be found that FM principle is universal in electrical machines. However, the researches of FM principle are still limited to some specific machines at present and it leads to the fragmentation of theory. A new general air-gap FM theory is introduced and it can be expected to be the unified theory for electrical machines. To verify the correctness of the new theory, some electrical machines, including induction machine and non-salient pole machine, are analyzed by the general air-gap FM theory. In addition, the design and engineering application of FM machine and theory is analyzed. To verify the inherent unity of electrical machine, the topology evolutions of FM machine are also discussed. Based on the new general air-gap FM theory, the innovative methods of topology can be summarized while the development prospects of FM machine are subsequently discussed.
23 July 2018 in IEEE Transactions on Industrial Electronics
Cost-effective and high-performance linear motors attract more and more attention for many applications. This paper is to propose a novel double side linear flux-modulation permanent-magnet (DS-LFMPM) motor with low cost, high thrust force density and high power factor. The novelty of the proposed DS-LFMPM motor is to improve power factor by using double side topology. Its topology is presented, and its operation principle is investigated. From the harmonic spectrums of the flux density in the air-gap before and after the modulation of the mover teeth and the stator teeth, it can be concluded that the proposed motor has good flux-modulation effect. Also, the expression of the orders of the harmonic spectrums is given. The design process of sizes and structure is particularly explained. The electromagnetic performances are predicted by using finite-element method and the proposed motor is prototyped for verification. The results show that the proposed DS-LFMPM motor can produce high thrust force density and high power factor.
24 September 2021 in IEEE Transactions on Transportation Electrification
In this article, the fault-tolerant control (FTC) strategy based on current redistribution is compared for three types of triple redundant $3\times 3$ -phase motor: surface-mounted permanent magnet synchronous motor (SPMSM), synchronous reluctance motor (SynRM), and permanent magnet-assisted synchronous reluctance motor (PMa-SynRM), under a single-phase open-circuit fault. The output torque of SPMSM and SynRM is produced by permanent magnet (PM) torque and reluctance torque, respectively. Nevertheless, for PMa-SynRM, it is necessary to determine the distribution ratio of PM torque and reluctance torque in the proposed FTC strategy. By comparing the FTC performance of motors, the conclusions are as follows: 1) torque ripple of the SPMSM can be completely suppressed; 2) torque ripple minimization for the SynRM and PMa-SynRM can be realized; and 3) optimal solution obtained in SynRM can also be applied to the PMa-SynRM when the load is heavy. In addition, to reduce the complexity and improve the reliability of the control system, a mono-inverter-driven triple-paralleled control system is constructed in healthy and postfault operations. The comparison results of the FTC strategy for three types of motor are obtained by simulation. And the experimental results based on a $3\,\times \,3$ -phase PMa-SynRM are accomplished to verify the feasibility of the theory.
8 May 2025 in IEEE Transactions on Industrial Electronics
This article proposes two types of dual excitation permanent magnet linear machine (DEPMLM) for long-distance application. By incorporating asymmetry in dual excitation, both the second-order harmonic magnetomotive force (MMF) in primary excitation (PE) and the second-order harmonic permeance in secondary excitation (SE) are effectively generated. The extended working harmonics generated on this basis can substantially enhance thrust force density. The article begins by describing the machine topology and operating principles under dual excitation. It then discusses the analytical modeling and thrust force generation mechanism based on multiple working harmonics, validated through finite element analysis (FEA). Next, it evaluates and compares the electromagnetic performance of DEPMLM with other PMLMs, followed by validation through a prototype. The results demonstrate that with dual excitation, the proposed DEPMLM achieves substantial increases in thrust force density—exceeding 98.1% and 79.1% compared to the existing asymmetric flux reversal PMLM and switched flux PMLM, respectively. Additionally, DEPMLM improves thrust force density by 40.6% while requiring only about 60% of the PMs used in conventional PMLMs with SE over a 10-m distance. DEPMLM thus emerges as a competitive and cost-effective solution for long-distance applications, outperforming existing PE-PMLMs and conventional PMLMs.
25 January 2018 in IEEE Transactions on Applied Superconductivity
This paper proposes a new modular-stator tubular permanent-magnet (PM) Vernier motor. The proposed motor offers a good fault-tolerant capability and an improved force performance, suitable for the electromagnetic active vehicle suspension. The proposed motor artfully integrates PM Vernier motors and tubular motors together, offering a zero-net radial force between the armature and mover, and the robust mover structure and high thrust force. Meanwhile, the modular complementary stator structure is designed to decouple the adjacent phase windings, hence offering the desired fault-tolerant capability. Moreover, the PMs with two magnetized directions are adopted, namely radially and axially. One is used to produce the main flux, while another can reduce fringing leakage flux, hence increasing the thrust force. The electromagnetic performances are analyzed by using the finite-element method, verifying the effectiveness of the theoretical analysis.
30 August 2023 in IEEE Transactions on Power Electronics
Sensorless control methods based on flux observer have been widely used in motor drives with medium-high speed operation. However, the conventional methods have some shortcomings in estimation accuracy due to the dc bias caused by the integration, measurement, and parameter uncertainty. In this article, a new frequency adaptive disturbance observer with band-pass filter characteristics is proposed. It is insensitive to dc bias and high-frequency noise, hence improving the robustness of the system. Since the proposed method has no phase delay at any synchronous rotor frequency and can amplify the amplitude of the estimated active flux, it does not need a phase compensation module and can obtain a wider operating range. Moreover, an adaptive extended state observer is added to estimate the disturbance caused by parameter mismatch. The estimated disturbance is fed back to the estimated active flux, which further improves the accuracy of the system. Finally, experiments based on a triple redundant permanent magnet-assisted synchronous reluctance motor are accomplished to verify the effectiveness and accuracy of the proposed observer.