29 December 2021 in Russian Microelectronics
In the process of manufacturing multichip modules based on chipless ICs with a matrix arrangement of contact pads, due to the large number of sequentially performed soldering operations, the melting temperature of the solder in the first operation should be at least 270°C. With a large number of small contact pads and a large distance between them, the formation of a solder layer of the given thickness is possible mainly only by electrodeposition. This paper presents the results of studying the process of the electrodeposition of a tin–lead alloy with a high lead content (more than 80% by weight) for the formation of a solder layer with a melting point of more than 270°C, intended for mounting crystals with a matrix arrangement of the contact pads in the technology of manufacturing multichip modules. The composition of the fluoroborate electrolyte is proposed, which ensures obtaining the given chemical composition of the alloy. The dependence of the chemical composition of the alloy on the current density during its formation is established. The value of the optimal current density is determined to be (1–1.2) A/dm2. At this current density, dense fine-grained layers with a melting point of about 290–295°C are formed.
8 December 2023 in Journal of Surface Investigation: X-Ray, Synchrotron and Neutron Techniques
Methods are proposed and criteria are established for preparing the surface of nanostructured thermoelectric materials for the deposition of thin- and thick-film ohmic contacts. The parameters of the mechanical and chemical methods of thermoelectric material surface treatment before the deposition of the contact. The roughness and morphology of the surface of thermoelectric material samples and the films obtained are studied. The criteria and optimal values of the surface roughness of thermoelectric materials are established. The conditions of obtaining thin- and thick-film contacts are determined. Thin-film contacts (thickness up to 300 nm) are obtained by the magnetron sputtering of Ni. Thick-film contacts are formed by the chemical and electrochemical deposition of Ni. The obtained films contain various amounts of Ni. The electrical resistivity of the Ni films obtained by chemical deposition is significantly higher than that of Ni films obtained by electrochemical deposition. The specific contact resistance of the metal–thermoelectric material system in the case of the deposition of Ni films by magnetron sputtering is the smallest among the considered samples. In the case of forming contacts by chemical deposition, it is comparable to that for Ni films formed by electrochemical deposition. The adhesion strength of Ni films obtained by various methods has high values exceeding the industry standard for film coatings in microelectronics. All obtained ohmic contacts satisfy the requirements for the construction of efficient thermoelements in terms of electrical properties and adhesion strength.
18 July 2024 in Žurnal prikladnoj himii
Предложен способ получения контактов на основе W–Ni и W–Co, выполняющих функции диффузионно-барьерных слоев в конструкции термоэлементов. Контакты сформированы электрохимическим осаждением пленок W–Ni и W–Co на образцах наноструктурированных термоэлектрических материалов на основе Bi2Te2.4Se0.6, Bi0.4Sb1.6Te3, GeTe и PbTe, используемых для изготовления термоэлементов. Получены пленки толщиной до 15 мкм с разбросом по толщине не более 5%. Содержание вольфрама в составе пленок W–Ni составило 33.5 мас%, в пленках W–Co — 29.7 мас%. Удельное сопротивление и удельное контактное сопротивление пленок составило 3.4∙10–7 Ом∙м и 3.8∙10–9 Ом∙м2 соответственно. Адгезионная прочность пленок составляет 10−13 МПа. Установлено, что контакты, сформированные на образцах термоэлектрических материалов электрохимическим осаждением пленок на основе W–Co, могут быть использованы в конструкции термоэлементов с рабочими температурами до 900 K.