20 February 2026 in IEEE Transactions on Antennas and Propagation
In this communication, a novel 1-bit programmable reflect-array antenna is proposed for wideband beam-steering applications in functionally integrated radio frequency (RF) systems. The proposed reflective element is characterized by a single-diode resonator with multiple resonant modes in both the ‘ON’ and ‘OFF’ states. By independently manipulating these modes to achieve an interleaved and equidistant distribution in the frequency spectrum, an extremely wideband 1-bit phase switching capability is realized. Simulation results indicate that the presented reflective element can generate a stable reflection phase reversal from 9.3 GHz to 21 GHz when the diode alternates between two states. For experimental validation, a 16 × 16 element reflect-array antenna was fabricated and measured. Measurement confirms that the proposed reflect-array antenna can achieve satisfactory radiation and beam-scanning performance over an 80% relative bandwidth. The flexible electromagnetic manipulation capability across a wide spectrum renders the proposed design highly applicable in advanced radiators and reconfigurable intelligent surfaces in next-generation RF systems.
1 March 2023 in IEEE Transactions on Antennas and Propagation
A metal-loading method (ML) is proposed in this paper to increase effective length, near-field magnitude and radiation efficiency for acoustically actuated piezoelectric antenna (PEA). Field-based circuit model method (FBCM) is utilized to characterize the metal-loaded piezoelectric antenna (MLPEA) by introducing antenna fields into piezoelectric equations and impedance analysis at boundary. Furthermore, current distribution within PE cylinder and on loaded metal rod is calculated by FEM method and formulated with piecewise functions. And, antenna effective length is evaluated with different loaded metal lengths and effects of the loaded metal are analyzed on antenna near-fields and radiation efficiency. All the methods are validated by measurement of a demonstrated MLPEA on a precise testing vehicle with frequency error of 0.05% and near-field magnitude error of 0.97dB. Finally, maximum increase of 4.6dB for near-field magnitude, and 10 times for radiation efficiency is obtained for PEA with loaded metal length of 0.8m. Different loss mechanisms in MLPEA are also analyzed and the radiation efficiency limit for PEA, as estimated by FBCM, is much larger than that of metallic antenna when ka is less than 0.1, leaving far more room for radiation efficiency elevation of PEA for the-state-of-art.
6 November 2023 in IEEE Transactions on Antennas and Propagation
This paper proposes a planar magneto-electric resonator (PMER) as the element of broadband dual-polarized (DP) and circularly-polarized (CP) reflectarray antennas (RAs). The PMER is realized by introducing a split in dual rhombic rings, which flats the vertical structure for magnetic resonance in common ME element. Owing to the isolated magnetic and electric resonant modes of the PMER, anisotropic characteristic is achieved to independently manipulate the reflection phase among two orthogonal polarizations and reflect CP incident wave in a wide bandwidth. Moreover, a simple modification method is presented for further expanding the operating band of CP element. For proof, a DP-RA and CP-RA prototype is fabricated and measured. The measured results reveal that 1-dB gain bandwidths of 17.5% / 22.2% and 25.6% are observed for DP- and CP-RA respectively, while maintaining low profiles and high aperture efficiencies. Especially, the measured axial ratio (AR) bandwidth of the PMER-based CP-RA reaches 66.7%.
30 September 2022 in IEEE Transactions on Antennas and Propagation
A field-based circuit model (FBCM) is proposed to reveal impedance, near-field, and far-field performance of acoustically actuated piezoelectric (PE) antenna by introduction of electromagnetic induction into piezoelectric equations and impedance analysis at boundary. To make the model more practical, induced current on PE antenna body is analyzed and near-field compression by large permittivity of piezoelectric material is formulated. Closed-form expressions are built to conveniently evaluate model parameters. Furthermore, the FBCM method is validated by precise vehicles, and calculation results agree with the measurement with maximum frequency error of 0.15% and near-field magnitude error of 3.9dB, all measured impedance and near-field components follow the characteristic described by FBCM. At last, radiation efficiency of a demonstrated PE antenna is calculated by FBCM to be 1.3e-9 for single unit and 2.0e-9 for PE antenna array which is 5-67 times higher than that of metallic electrical small antenna of the same size. The FBCM method can be an effective and convenient way for researchers to design and evaluate PE antennas in a short time.
18 August 2025 in IEEE Transactions on Microwave Theory and Techniques
The existing wideband methodology of 1-bit programmable metasurface commonly relies on spatial rotation or open/short switching of the integrated transmission line within the receiver/radiator. It implies that the bandwidth is naturally restricted by the basic components, such as the polarization converters or radiators. In this article, a novel mode-transforming scheme is proposed to break the limitation and enable the wideband programmable metasurface realization. By controlling the state of diodes inserted within the resonator, the meta-atom can be transformed between dual resonance and single resonance with specific eigenfrequencies, achieving a wideband reflection phase reversal. Furthermore, a hybrid compensation method is developed to relieve the degeneration caused by the parasitic effect of physical diodes. A unit cell sample and metasurface antenna prototype are manufactured and measured, yielding a satisfactory performance across the 9–16.5-GHz band, equivalent to 58.8% bandwidth. Within the operating band, the metasurface antenna can achieve 2-D beam-scanning coverage up to ±60°. All these validated results demonstrate the excellent performance of the proposed programmable metasurface, highlighting its potential for diverse applications in electromagnetic wave manipulation.
18 August 2025 in IEEE Transactions on Microwave Theory and Techniques
One of the primary objectives of 2-D inverse scattering problems (ISPs) is to accurately characterize the nature of an unknown tomographic domain based on the collected scattered field data. While numerous existing iterative algorithms for ISPs have been successfully applied to reconstruct various scatterers, they are often computationally expensive and prone to becoming trapped in local minima during optimization. On the other hand, approaches that combine learning methods can solve ISPs rapidly and accurately but often lack the generality of purely data-driven methods. Therefore, achieving a balance between the generality of traditional iterative methods and the efficiency and accuracy of learning-based approaches remains a significant challenge. In this work, we introduce a physics-informed and transformer-embedded neural network with the optimization objective of the contrast source inversion (CSI) method, termed PiTCSI, to bridge this gap. The promising results demonstrate that PiTCSI achieves reconstruction quality comparable to representative methods requiring only half of the training data. By the way, the results on multiple experimental datasets demonstrate the effectiveness of the approach for reconstruction from measured scattering data.