Andrew Morgan Williams

Andrew Morgan Williams

Auto-generated profile, based on publicly available information

Andrew Morgan Williams

Loughborough Univ

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2021 in Atmospheric Environment
Verified
Journal Article
Closed access
Roy HarrisonRoy Harrison
Roy Harrison
JAJames Allan
James Allan
DCDavid Carruthers
David Carruthers
MHMathew Heal
Mathew Heal
ALAlastair C. Lewis
Alastair C. Lewis
AWAndrew Williams
Andrew Williams

19 May 2003 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
HXHongming Xu
Hongming Xu
AWAndrew Williams
Andrew Williams
HFHuiyu Fu
Huiyu Fu
SWStan Wallace
Stan Wallace
SRSteve Richardson
Steve Richardson
MRMike Richardson
Mike Richardson
A single zone combustion model based on a chemical kinetic solver has been combined with a one-dimension thermo/gas dynamic engine simulation code to study the operating characteristics of a V6 engine in which Homogeneous Charge Compression Ignition (HCCI) operation (also referred to as ‘Controlled Auto-ignition” CAI) is enabled by a cam profile switching (CPS) system with negative valve overlap. An operational window within which HCCI combustion is possible has been identified and the limit of HCCI operating region for varied valve lift possibilities is explored. The mechanisms and potential fuel economy improvements within the HCCI envelope are studied and modelled results compared against data from similar engines. It is shown that for the best fuel economy the valve timing strategy needs to be selected very carefully, despite the engine's capability to operate at a range of valve timing combinations. The heating effect of the exhaust gases is dominant when using less than approximately 55% residual gases. For higher EGR rates, the diluting effect coupled with reducing exhaust gas temperatures makes the ignition timing retarded. It is demonstrated that for HCCI operation the selection of valve lift for the CPS system is limited between the constraints of the breathing capacity with the lower valve lift and misfires with the higher one.

1 November 2008 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Open access
AWA M Williams
A M Williams
CGC P Garner
C P Garner
JBJ G P Binner
J G P Binner
Gel-cast ceramic foams potentially offer a more robust configurable alternative filtration medium to monolithic wall flow filters (WFFs) for the reduction in particulate matter (PM) emissions from diesel internal combustion engines. The fundamental back pressure and filtration efficiency characteristics of gel-cast ceramic foam diesel particulate filters (DPFs) have been investigated. Methodology is developed for the first time that allows the calculation of the effect of local PM loading on the pressure drop characteristics from experimental data without problems caused by the non-uniform PM loading in the filter that can be applied to all depth bed filtration media. The back pressure and filtration efficiency relationships were used to develop graphical design spaces to aid development of application-specific DPFs. Effects of PM distribution on the pressure drop of the filter are presented. Filters with a non-even distribution of PM were found to have lower pressure drops than filters with an evenly distributed PM for the same average specific PM loadings. The predictions showed that gel-cast ceramic foams can achieve comparable back pressure, filtration volume, and PM holding capacity with WFFs with a lower filtration efficiency of about 80 per cent. The model demonstrated that greater than 90 per cent filtration efficiency can be achieved with filter volumes of about 0.6 times the volume of a WFF with a lower PM holding capacity.

2 September 2008 in Journal of the American Ceramic Society
Verified
Journal Article
Open access
PDF file
AWAndrew M. Williams
Andrew M. Williams
CGColin P. Garner
Colin P. Garner
JBJon G.P. Binner
Jon G.P. Binner
Increasing applications for gelcast ceramic foams is making the effective, accurate and cost effective measurement of pore diameter and distribution of significant value to a wide range of research fields. Current methods either do not directly measure pore diameter or they require high equipment and time costs. Measuring pore diameter directly from sample cross sections is both rapid and cost effective but, due to the random nature of the pore location during sectioning of the sample, it under predicts the pore diameter. The proposed method identified that the mean measured pore diameter was 79% (2 s.f.) of the actual pore diameter. Numerical methods for correcting the pore distribution as well as the average pore diameter are presented.

12 April 2011 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Open access
PDF file
AWAndrew M Williams
Andrew M Williams
ABAlan T Baker
Alan T Baker
CGColin P Garner
Colin P Garner
The importance of new technologies to improve the performance and fuel economy of internal combustion engines is now widely recognized and is essential to achieve CO₂ emissions targets and energy security. Increased hybridization, combustion improvements, friction reduction and ancillary developments are all playing an important part in achieving these goals. Turbocharging technology is established in the diesel engine field and will become more prominent as gasoline engine downsizing is more widely introduced to achieve significant fuel economy improvements.The work presented here introduces, for the first time, a new technology that applies conventional turbomachinery hardware to depressurize the exhaust system of almost any internal combustion engine by novel routing of the exhaust gases. The exhaust stroke of the piston is exposed to this low pressure leading to reduced or even reversed pumping losses, offering ≻5% increased engine torque and up to 5% reduced fuel consumption. This method has the distinct advantage of providing performance and fuel economy improvements without significant changes to the structure of the engine, the combustion system or lubrication system.The Turbo-Discharging concept is introduced and analyzed. A combination of filling/emptying models and 1-D gas dynamic simulations were used to quantify the energy flows and identify optimum valve timings and turbomachine characteristics. 1-D gas dynamic simulation was then used to predict primary fuel economy benefits from Turbo-Discharging. Secondary benefits, such as extended knock limits are then discussed.

20 January 2013 in Plasma Chemistry and Plasma Processing
Verified
Journal Article
Closed access
PDF file
KGK. Graupner
K. Graupner
JBJon Binner
Jon Binner
NFN. Fox
N. Fox
CGC. P. Garner
C. P. Garner
JHJ. E. Harry
J. E. Harry
AWA. M. Williams
A. M. Williams