Hongye Huang

Hongye Huang

Auto-generated profile, based on publicly available information

Hongye Huang

Department of Electrical and Electronic Engineering, Institute of Science Tokyo, Tokyo, Japan

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 March 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
JPJian Pang
Jian Pang
RWRui Wu
Rui Wu
YWYun Wang
Yun Wang
MDMasato Dome
Masato Dome
HKHisashi Kato
Hisashi Kato
KOKenichi Okada
Kenichi Okada
This paper presents a 28-GHz CMOS four-element phased-array transceiver chip for the fifth-generation mobile network (5G) new radio (NR). The proposed transceiver is based on the local-oscillator (LO) phase-shifting architecture, and it achieves quasi-continuous phase tuning with less than 0.2-dB radio frequency (RF) gain variation and 0.3° phase error. Accurate beam control with suppressed sidelobe level during beam steering could be supported by this work. At 28 GHz, a single-element transmitter-mode output P1,dB of 15.7 dBm and a receiver-mode noise figure (NF) of 4.1 dB are achieved. The eight-element transceiver modules developed in this work are capable of scanning the beam from -50° to +50° with less than -9-dB sidelobe level. A saturated equivalent isotropic radiated power (EIRP) of 39.8 dBm is achieved at 0° scan. In a 5-m over-the-air measurement, the proposed module demonstrates the first 512 quadrature amplitude modulation (QAM) constellation in the 28-GHz band. A data stream of 6.4 Gb/s in 256-QAM could be supported within a beam angle of ± 50°. The achieved maximum data rate is 15 Gb/s in 64-QAM. The proposed transceiver chip consumes 1.2 W/chip in transmitter mode and 0.59 W/chip in receiver mode.

27 May 2020 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
JPJian Pang
Jian Pang
ZLZheng Li
Zheng Li
RKRyo Kubozoe
Ryo Kubozoe
XLXueting Luo
Xueting Luo
RWRui Wu
Rui Wu
KOKenichi Okada
Kenichi Okada
This article presents a low-cost and area-efficient 28-GHz CMOS phased-array beamformer chip for 5G millimeter-wave dual-polarized multiple-in-multiple-out (MIMO) (DP-MIMO) systems. A neutralized bi-directional technique is introduced in this work to reduce the chip area significantly. With the proposed technique, completely the same circuit chain is shared between the transmitter and receiver. To further minimize the area, an active bi-directional vector-summing phase shifter is also introduced. Area-efficient and high-resolution active phase shifting could be realized in both TX and RX modes. In measurement, the achieved saturated output power for the TX-mode beamformer is 15.1 dBm. The RX-mode noise figure is 4.2 dB at 28 GHz. To evaluate the over-the-air performance, 16 H+16 V sub-array modules are implemented in this work. Each of the sub-array modules consists of four 4 H+4 V chips. Two sub-array modules in this work are capable of scanning the beam from -50° to +50°. A saturated EIRP of 45.6 dBm is realized by 32 TX-mode beamformers. Within 1-m distance, a maximum SC-mode data rate of 15 Gb/s and the 5G new radio downlink packets transmission in 256-QAM could be supported by the module. A 2x 2 DP-MIMO communication is also demonstrated with two 5G new radio 64-QAM uplink streams. Thanks to the proposed area-efficient bi-directional technique, the required core area for a single element-beamformer is only 0.58 mm². Compact and low-cost 5G millimeter-wave MIMO systems could be realized.

6 January 2021 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
JPJian Pang
Jian Pang
ZLZheng Li
Zheng Li
XLXueting Luo
Xueting Luo
JAJoshua Alvin
Joshua Alvin
RSRattanan Saengchan
Rattanan Saengchan
KOKenichi Okada
Kenichi Okada
This article introduces a power-efficient and low-cost CMOS 28-GHz phased-array beamformer supporting fifth-generation (5G) dual-polarized multiple-in-multiple-out (MIMO) (DP-MIMO) operation. To improve the cross-polarization (cross-pol.) isolation degraded by the antennas and propagation, a power-efficient analog-assisted cross-pol. leakage cancellation technique is implemented. After the high-accuracy cancellation, more than 41.3-dB cross-pol. isolation is maintained along with the transmitter array to the receiver array. The element-beamformer in this work adopts the compact neutralized bi-directional architecture featuring a minimized manufacturing cost. The proposed beamformer achieves 22% per path TX-mode efficiency and a 4.9-dB RX-mode noise figure. The required on-chip area for the beamformer is only 0.48 mm 2 . In over-the-air measurement, a 64-element dual-polarized phased-array module achieves 52.2-dBm saturated effective isotropic radiated power (EIRP). The 5G standard-compliant OFDMA-mode modulated signals of up to 256-QAM could be supported by the 64-element modules. With the help of the cross-pol. leakage cancellation technique, the proposed array module realizes improved DP-MIMO EVMs even under severe polarization coupling and rotation conditions. The measured DP-MIMO EVMs are 3.4% in both 64-QAM and 256-QAM. The consumed power per beamformer path is 186 mW in the TX mode and 88 mW in the RX mode.

1 February 2019
Verified
Conference Paper
Closed access
JPJian Pang
Jian Pang
ZLZheng Li
Zheng Li
RKRyo Kubozoe
Ryo Kubozoe
XLXueting Luo
Xueting Luo
RWRui Wu
Rui Wu
KOKenichi Okada
Kenichi Okada
5G NR service will provide extremely-high-speed mobile data access using the millimeter-wave spectrum. To further boost the data-rate and spectrum efficiency, dual-polarized MIMO (DP-MIMO) will be introduced [1-4]. Separated beamformer arrays will be required for H and V polarizations. However, the increased free-spacepath-loss for the 5G NR band n257 (26.5GHz to 29.5GHz) demands numerous elements to cover enough communication distance. Concerning the required considerable number of chips, an area-efficient design will be necessary for a DPMIMO system targeting 5G NR FR2. This paper presents a 28GHz 4H+4V bi-directional beamformer chip supporting DP-MIMO in 65nm CMOS. The proposed neutralized bi-directional amplifier significantly reduces the required on-chip area. A bi-directional vector-summing phase shifter is also introduced. The measured RMS phase and gain errors are 0.4° and 0.2dB at 28GHz, respectively. The array module achieves a saturated EIRP of 45.6dBm/pol. at 0° scan with a 32H+32V array. In a 1m OTA measurement, a 4×4 sub-array module supports single-carrier data-rates of 15Gb/s and 6.4Gb/s per polarization in 640AM and 2560AM, respectively. The measured 400MHz OFDMA TX-to-RX EVM for the 4×4 sub-array module at 0° scan is -34.4dB in 2560AM. 2×2 DP-MIMO communication with a 400MHz 5G NR channel bandwidth is also achieved with a 64-0AM EVM of 4.9% for the 4×4 sub-array module.

1 December 2018 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
HLHanli Liu
Hanli Liu
ZSZheng Sun
Zheng Sun
DTDexian Tang
Dexian Tang
HHHongye Huang
Hongye Huang
TKTohru Kaneko
Tohru Kaneko
KOKenichi Okada
Kenichi Okada
This paper presents a Bluetooth low-energy (BLE) transceiver (TRX) achieving ultra-low-power operation for Internet-of-Things (IoT) applications. The proposed TRX utilizes a wide-bandwidth low-power fractional-N digital phase-locked loop (DPLL) as a central component to perform multiple roles: a direct frequency modulator for the transmitter (TX), an analog-to-digital converter (ADC) for the receiver (RX), a local oscillator for RX, and a frequency and phase synchronizer for the RX. The DPLL-based single-path downconversion method is adapted to halve the analog baseband circuit to further reduce the power consumption while maintaining a high interference rejection. A DPLL-based ADC with a digital-to-analog converter feedback greatly improves the ADC dynamic range, which improves the RX sensitivity and interference tolerance. By maximally reducing the required radio frequency and analog front-end components in RX, an RX power consumption of 2.3 mW is achieved with a -94 dBm sensitivity. The RX also satisfied all interference requirements with a certain margin. A 5.0-mW TX is achieved when delivering an output power of 0 dBm with a frequency-shift keying error of only 1.89%.

12 September 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
HLHanli Liu
Hanli Liu
ASAtsushi Shirane
Atsushi Shirane
KOKenichi Okada
Kenichi Okada
ZSZheng Sun
Zheng Sun
HHHongye Huang
Hongye Huang
TSTeruki Someya
Teruki Someya
This article proposes a fractional-N digital phase-locked loop (DPLL) that achieves a 265-μW ultra-low-power operation. The proposed switching feedback can seamlessly change the DPLL from sampling operation to sub-sampling operation without disturbing the phase-locked state of the DPLL to reduce the number of building blocks that works at the oscillator frequency, leading to significant power reduction. With the reduced number of high-frequency circuits, scaling the reference frequency is fully used to reduce the power consumption of the DPLL. Together with an out-of-dead-zone detector and a duty-cycled frequency-locked loop running in the background, the switching feedback achieves robust frequency and phase acquisition at start-up and helps the sub-sampling PLL recover when large phase and frequency disturbances occur. A transformer-based stacked-gm oscillator is proposed to minimize the power consumption while providing the sufficient swing to drive the subsequent stages. A truncated constant-slope digital-to-time converter is proposed to improve the power efficiency while retaining good linearity. The proposed fractional-N DPLL consumes only 265 μW while achieving an integrated jitter of 2.8 ps and a worst case fractional spur of -52 dBc, which corresponds to a figure of merit (FOM) of -237 dB.