8 December 2015 in Physical Review E
We investigate the loading and unloading behavior of soft solids in adhesive contact with randomly rough profiles. The roughness is assumed to be described by a self-affine fractal on a limited range of wave vectors. A spectral method is exploited to generate such randomly rough surfaces. The results are statistically averaged, and the calculated contact area and applied load are shown as a function of the penetration, for loading and unloading conditions. We found that the combination of adhesion forces and roughness leads to a hysteresis loading-unloading loop. This shows that energy can be lost simply as a consequence of roughness and van der Waals forces, as in this case a large number of local energy minima exist and the system may be trapped in metastable states. We numerically quantify the hysteretic loss and assess the influence of the surface statistical properties and the energy of adhesion on the hysteresis process.
30 September 2020 in Granular Matter
In this work, Discrete Elements Method simulations are carried out to investigate the effective stiffness of an assembly of frictional, elastic spheres under anisotropic loading. Strain probes, following both forward and backward paths, are performed at several anisotropic levels and the corresponding stress is measured. For very small strain perturbations, we retrieve the linear elastic regime where the same response is measured when incremental loading and unloading are applied. Differently, for a greater magnitude of the incremental strain a different stress is measured, depending on the direction of the perturbation. In the case of unloading probes, the behavior stays elastic until non-linearity is reached.Under forward perturbations, the aggregate shows an intermediate inelastic stiffness, in which the main contribution comes from the normal contact forces. That is, when forward incremental probes are applied the behavior of anisotropic aggregates is an incremental frictionless behavior. In this regime we show that contacts roll or slide so the incremental tangential contact forces are zero. Graphical Abstract
1 October 2017 in Journal of the Mechanical Behavior of Biomedical Materials
25 November 2016 in European Journal of Ophthalmology
Purpose: To investigate the adhesive and stiffness properties of prestripped Descemet membrane endothelial keratoplasty (DMEK) lenticules in different preservation conditions (with and without dextran). Methods: The study included 3 conditions: (C1) tissues collected from tissue culture media (TCM), stripped and preserved in TCM; (C2) tissues collected from transport media (TM) (TCM supplemented with 6% dextran T-500), stripped and preserved in TM; and (C3) tissues collected from TCM, stripped and preserved in TM. Using a hinge, 9.5-mm stripped DMEK lenticules were restored back on the stroma and preserved for 4 days at room temperature (RT) in different conditions as above. Nine tissues, 3 from each condition, were used to check the adhesive (fibronectin, laminin, and vitronectin) and elastic properties (fibrillin, elastin, and collagen VI) using different antibodies. Six tissues, 2 from each condition, were used to check the stiffness properties after preservation using atomic force microscopy (AFM) nanoindentation method. Results: On the Descemet membrane, fibronectin was strongly expressed in C2 and C3, whereas laminin was intense in C2 postpreservation. Vitronectin was expressed in all the conditions. Elastic proteins were not expressed in either of the conditions apart from collagen VI, which was expressed on the posterior stroma. Atomic force microscopy showed higher stiffness in C3 and an insignificant but lower rigidity in C2 as compared to C1. Conclusions: The tissues from C2 showed expression of adherent proteins and lower stiffness. Dextran may be suitable in preservation of DMEK grafts before and after preparation. Less stiff tissues may help reduce manipulations required in the recipient eye during DMEK surgery.
8 November 2015 in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
We consider a random aggregate of identical, frictionless spheres whose contact is maintained by an applied pressure. The aggregate is then subjected to an axial compression at fixed pressure. We show that the incremental elastic response of the resulting transversely isotropic material is characterized by six rather than by five independent coefficients and that the stiffness tensor does not have the major symmetry. This is because we permit deviations from an affine deformation that are determined by local equilibrium, when anisotropy is present. Discrete element numerical simulations confirm these findings.
19 December 2016 in Physical Review E
In this paper, we deal with anisotropy in an idealized granular material made of a collection of frictional, elastic, contacting particles. We present a theoretical analysis for an aggregate of particles isotropically compressed and then sheared, in which two possible contacts laws between particles are considered: a linear contact law, where the contact stiffness is constant; and a nonlinear contact law, where the contact stiffness depends on the overlapping between particles. In the former case the anisotropy observed in the aggregate is associated with particle arrangement. In fact, although the aggregate is initially characterized by an isotropic network of contacts, during the loading, an anisotropic texture develops, which is measured by a fabric tensor. With a nonlinear contact law it is possible to develop anisotropy because contacting stiffnesses are different, depending on the orientation of the contact vectors with respect to the axis of the applied deformation. We find that before the peak load is reached, an aggregate made of particles with a linear contact law develops a much smaller anisotropy compared with that of an aggregate with a nonlinear law.