28 July 2024 in Solar Energy Materials and Solar Cells
1 November 2023 in Journal of Renewable and Sustainable Energy
Cu2O-based solar cells offer a promising solution to address future energy challenges due to their affordability, eco-friendliness, and impressive power conversion efficiency (PCE). With the development of thin film deposition technology, the maximum PCE of single-junction solar cells fabricated based on Cu2O is 9.5%. Because the spectral sensitivity overlaps between Cu2O and crystalline silicon (c-Si) is small, Cu2O thin-film solar cells can be made into tandem solar cells with Si-based solar cells to achieve higher PCE. The Cu2O–Si tandem solar cell has been delivered 24.2% PCE in 2020, a time when the PCE of stand-alone silicon solar cells was 17.6%. The purpose of this paper is to summarize the development of Cu2O-based heterojunction, homojunction. The Cu2O material properties, n and p-type doping, the role of defects and impurities in bulk of films or at the interface of the p–n-junction and n-type buffer layer on the performance of Cu2O-based heterojunction like ZnO–Cu2O, and the difficulty in decreasing the interface state and doping in Cu2O homojunction solar cells are discussed. This review discusses the Cu2O film material preparation method, the history of Cu2O based solar cells, the essential factors required to enhance the performance of various types of Cu2O-based solar cells, and the potential future research opportunities for as a top subcells in Cu2O–Si tandem solar cells.
10 October 2026 in ACS Applied Materials & Interfaces
18 August 2026 in Energy & Environmental Science
A multifunctional additive Na[B(C 2 O 4 )F 2 ] regulates crystallization and band alignment in wide-bandgap perovskites. Tandem cells achieve 34.28% certified efficiency (1.001 cm 2 ) and retain >93% after 2000 h at 65 °C.
22 May 2026 in Advanced Energy Materials
Conventional phosphonic acid‐based SAMs, exemplified by [4‐(3,6‐dimethoxy‐9H‐carbazol‐9‐yl)butyl]phosphonic acid (MeO‐4PACz), readily aggregate, leading to non‐uniform buried‐interface coverage and constrained device output. Here, we engineer co‐assembled SAMs (Co‐SAMs) by co‐assembling MeO‐4PACz with trimethoxysilane‐anchored terminal siloxanes—epoxy (GOPS), thiol (TMSPT) and isocyanate (IPTMS)—to homogenize the NiO
x
/perovskite contact. The resulting Co‐SAMs form denser and more uniform interfacial layers on NiO
x
, boosting the open‐circuit voltage ( V oc ) and fill factor (FF) of 1.68 eV wide‐bandgap perovskite solar cells, with IPTMS‐based Co‐SAMs delivering the largest improvement. Performance correlates with a distinct evolution of siloxane‐mediated intermolecular interactions. We demonstrate that the evolution of intermolecular interactions from physical blending (MeO4‐GOPS) and specific hydrogen bonding (MeO4‐TMSPT) to covalent bridging (MeO4‐IPTMS) significantly enhances interfacial quality. Specifically, the phosphonate–carbamate covalent bridge formed in MeO4‐IPTMS most effectively suppresses aggregation and delivers synergistic defect passivation. Leveraging this strategy, monolithic perovskite/silicon tandem cells deliver a champion power conversion efficiency (PCE) of 33.74% (certified 33.37%). Furthermore, the devices exhibit exceptional stability, showing negligible degradation after 4000 h of dark storage and retaining 87.12% of their initial PCE after 1000 h of maximum power point tracking (MPPT) under continuous one‐sun illumination, highlighting the potential of this interfacial strategy for highly stable tandem photovoltaics.