21 February 2005 in Progress in Structural Engineering and Materials
1 October 2000 in Journal of Structural Engineering
Widespread occurrence of brittle beam-to-column connection fracture has been discovered in steel frame buildings after 1994 Northridge and 1995 Hyogoken-Nanbu earthquakes. To investigate the effects of connection failure on structural response of steel buildings under earthquakes, a smooth connection-fracture hysteresis model based on the Bouc-Wen model is developed. It can reproduce the hysteretic characteristics found in cyclic loading tests of the FEMA/SAC (SEAOC, ATC, CUREe) steel project. To account for the effects of flexible floor systems, biaxial interaction, and torsional motion, a 3D inelastic structural analysis model developed by the writers is used. From a numerical study, it was found that for response evaluation of strong-column, weak-beam type steel buildings a conventional shear-building model assuming rigid floor systems is not adequate. The response behavior of steel buildings with connection fractures may only be moderately altered if there is some residual strength after the fracture....
1 January 2006 in Journal of Structural Engineering
The minimum weight criterion, which has been widely adopted in the literature for optimal design of steel structural systems, is inadequate to fully reflect the initial monetary investment due to lack of consideration of additional construction expenses resulting from varied degree of design complexity such as different member sections and splice/connection types. In this paper, design optimization of seismic steel moment-resisting frames involves simultaneous consideration of two competing objective functions: the steel material weight and an approximate measure of design complexity in terms of the number of different standard steel member section types. The code-compliant seismic structural design follows the equivalent lateral force procedure of the 2000 National Earthquake Hazards Reduction Program seismic provisions in conjunction with American Institute of Steel Construction load resistance factor design seismic steel design criteria. A genetic algorithm is used for the posed biobjective structural optimization problem to produce a set of alternative designs establishing optimized trade-off between the two merit objectives. Numerical examples show that a minimum weight design with a balanced degree of design complexity is expected to achieve an initial investment economy with more accuracy.
1 March 2007 in Journal of Structural Engineering
For performance evaluation of structural systems under seismic loads, accurate modeling of structural component and system response behavior in the nonlinear range is required. In this study, the differential-equation-based hysteresis (Bouc-Wen) model is incorporated into ABAQUS to describe the inelastic connection behaviors of moment frames, taking into account capacity uncertainties of connections documented in the FEMA/SAC projects. A three-dimensional (3D) finite-element model is developed to examine the effects of bi-axial motions including those due to torsion oscillation. Effects of gravity frames, panel zones, and inelastic column deformation are also considered. Numerical examples are carried out to evaluate displacement demand. System capacity against incipient collapse is determined by the incremental dynamic analysis (IDA). Both inherent variability and modeling error are considered. Results indicate that torsional effects due to asymmetric member failures are important. The conventional lumpe...
1 October 2000 in Journal of Structural Engineering
The redundancy of building structures under earthquake ground motion attracted more attention after the 1994 Northridge and 1995 Kobe earthquakes. Very little, however, is known on redundancy under stochastic dynamic loads primarily due to the analytical difficulty associated with such problems. This paper proposes a method for evaluation of structural reliability and redundancy of steel buildings under earthquakes in terms of maximum column drift ratio (MCDR). The seismic hazard is expressed in terms of annual exceedance probability of biaxial spectral displacement (BSD). A power law relationship between MCDR and BSD is then established from regression analyses of building response under SAC (SEAOC, ATC, CUREe) ground motions for a wide range of intensity. The annual exceedance probability of MCDR is then determined from the BSD hazard curve for a given MCDR threshold multiplied by a correction factor for the capacity and modeling uncertainties. The effects of brittle connection failure, biaxial interaction, and torsional motion are examined. A uniform-risk redundancy factor is also developed for calculating the required design force for structures of different degrees of redundancy such that a uniform reliability requirement is satisfied.
1 March 2007 in Journal of Structural Engineering
In NEHRP 2003, a new mechanism-based reliability/redundancy factor, ρ , is proposed to replace the current ρ factor in building codes. A multiplier of ρ=1.3 for design lateral force is recommended for structures deemed being lack of redundancy. The effects of detailed structural configurations, nonlinear structural behaviors, and uncertainty in demand and capacity, however, have not been considered in this factor. To examine the adequacy of this new factor, a systematic investigation on the above effects is carried out. It focuses on buildings with 5×5 bays and nine different configurations of special moment resisting frames. The nonlinear structural response behaviors and uncertainty in demand and capacity based on a three-dimensional (3D) incremental dynamic analysis are properly considered. Structural reliability and redundancy are determined. The biaxial spectral acceleration is found to be a more effective predictor of system demand than drift and therefore used as the response measure in the analysi...