27 March 2023 in Gospodarka Surowcami Mineralnymi - Mineral Resources Management
In order to explore the impact of coal and gangue particle size changes on recognition accuracy and to improve the single particle size of coal and gangue identification accuracy of sorting equipment, this study established a database of different particle sizes of coal and gangue through image gray and texture feature extraction, using a relief feature selection algorithm to compare different particle size of coal and gangue optimal features of the combination, and to identify the points and particle size of coal and gangue. The results show that the optimal features and number of coal and gangue are different with different particle sizes. Based on visible-light coal and gangue separation technology, the change of coal and gangue particle size cause fluctuations in the recognition accuracy, and the fluctuation of recognition accuracy will gradually decrease with increases in the number of features. In the process of particle size classification, if the training model has a single particle size range, the recognition accuracy of each particle size range is low, with the highest recognition accuracy being 98% and the average recognition rate being only 97.2%. The method proposed in this paper can effectively improve the recognition accuracy of each particle size range. The maximum recognition accuracy is 100%, the maximum increase is 4%, and the average recognition accuracy is 99.2%. Therefore, this method has a high practical application value for the separation of coal and gangue with single particle size.
10 June 2024 in Archives of Mining Sciences
The gas emission from the goaf generates gas in the upper corner of the working face, and the return airflow exceeds safe limits. The identification of the reasonable level of the high-long borehole is the key factor to ensure the effectiveness of its extraction. On-site test at the 2308 working face of Licun Coal Industry of Lu’an Chemical Industry Group, the development of coal overlying strata fracture was studied through derivation of theoretical and empirical formulae, physical similarity experiment, and UDEC numerical simulation: this was then combined with in-situ microseismic monitoring to obtain the distribution characteristics of mining overburden “falling zone” and “overbreak zone” under the actual working conditions, and accurately design the high-level long borehole end hole layer. The results show that the height of the falling zone is 17.5 m to 20.5 m, and the overbreak zone is 43.5 m to 49.5 m. When the hole position is between 25 m and 30 m in the middle and lower part of the overbreak zone, the flow and concentration of gas extracted by drilling are high, and the pure amount of gas extracted by a single hole is increased by 53% (on average). The investigation of pressure relief gas extraction shows that throughout the mining period, the average gas concentration in the return airway is maintained below 0.36%, and the average gas concentration in the upper corner is kept within 0.48% (effective gas control). The research proves the rationality of the arrangement of the high-level long borehole horizon in the working face and provides a reference for the design of the borehole horizon in the future gas drainage and control in the goaf.
3 March 2020 in Archives of Electrical Engineering
In order to meet the application requirements of high-power mobile inductively-coupled power transfer (ICPT) equipment, the structure of the dual transmitter and pickup can be used to improve the transmission power of the ICPT system. However, this structure cannot easily describe the change of the mutual inductance parameter in the moving state, making the mathematical model difficult to establish. The change of load parameters during the movement will affect the current and voltage at the transmitter and pickup coils. Aiming at these problems, this paper proposes a dual transmitter and pickup ICPT system based on inductor-capacitor-inductor (LCL) compensation network, and analyzes its power trans- mission efficiency. By setting the shape and size of the coil, the influence of the change of the mutual inductance parameters on the system efficiency during the movement is reduced. The changes of the mutual inductance parameters of the ICPT system under the moving state are simulated by changing the coupling coefficient in the PSpice software. The results show that the structure of the ICPT system used in this paper can improve the output power and reduce the influence of the system when the load changes.
25 June 2025 in Archives of Metallurgy and Materials
Gas utilization rate is a very important production parameter in the ironmaking blast furnace (BF), which can effectively reflect the utilization of fuel chemical energy. While hydrogen rich gas (such as shale gas) was injected into BF, with the introduction of CH4 in the hydrogen rich gas, the traditional calculation formula for the utilization rate of binary mixed gas (H2-CO) was no longer suitable for the calculation of the utilization rate of ternary mixed gas (CH4-H2-CO). Based on the principle of oxygen migration in the gas-solid reduction reaction, this paper established and derived the method for calculating the utilization rate of mixed gas after methane-rich gas was injected into BF (the mixed gas changes from H2-CO type to CH4-H2-CO type), it is helpful to analyze the influence of CH4 introduction in hydrogen rich gas on the utilization rate of mixed gas in reduction reaction after injecting hydrogen rich gas. In this paper, the change of gas utilization rates and physical phases of 0.5 mol Fe2O3, 0.5 mol V2O5 and 1 mol TiO2 reduced by different amounts of H2-CO or CH4-H2-CO at 700℃, 850℃ and 1000℃ were studied respectively, some meaningful results were obtained through comparative analysis, which provides a theoretical basis for methane rich gas injection practice of vanadium titanium magnetite blast furnace (VTM-BF).
10 February 2025 in Archives of Electrical Engineering
The integration of photovoltaic and the energy storage system into traction power supply systems under railway power conditioner (RPC) or voltage source converter (VSC) access structures changes the original pure AC system into a hybrid AC/DC system. At the same time, which access structure of photovoltaic and the energy storage system has higher system stability and which has better adaptability are rarely mentioned in the stability analysis of traction power supply systems with photovoltaic and the energy storage system. Firstly, in this paper, impedance models for the two types of access structures of photovoltaic and energy storage systems are established, and the port impedance characteristics and stability influencing factors are analyzed from the aspects of system parameters and controller parameters. Second, combining the two typical working conditions of PV and the ESS access traction power system, from the perspective of stability, the robustness of the two access structures under the influence of negative impedance characteristics and the adaptability of access are compared. Compared to traditional stability analysis methods, the GMPM (Gain Margin and Phase Margin) criterion employed in this paper integrates both the dynamic characteristics and frequency response of the system, making it particularly suitable for small-signal stability analysis. Keeping the rest of the conditions the same under two typical working conditions, the RPC access structure has higher system stability when the two access structures input and output 35kWof active power, respectively. Finally, the simulation results in the MATLAB/Simulink simulation platform also confirm the better adaptability of the RPC access structure.
18 December 2023 in Archives of Metallurgy and Materials
This paper conducts low temperature welding tests on Q460GJC thick plate (60 mm), and based on the basic theory of phase transformation structure evolution, a three-dimensional microstructure evolution analysis method for large welded joints is established, and the analysis of the evolution process of multi-layer and multi-pass weld structure under the low temperature environment of thick plates is completed. The comparison and analysis of test and numerical simulation results are in good agreement, which proves that the welding phase transformation model realizes the digitalization of metallurgical phase transformation in steel structure welding, and optimizes welding process parameters. It is of great significance to improve the quality of welding products and lay a foundation for predicting the performance of welded joints from the micro level.