5 February 2020 in IEEE Access
We consider a two-phase decode-and-forward (DF) relay network assisted by an unmanned aerial vehicle (UAV), where the UAV performs energy harvesting and information decoding simultaneously with a power splitting (PS) receiver structure. For the network, we optimize the PS and time allocation (TA) factors to minimize the outage probability in transferring the data from a source to a destination suffering from blockages in the direct link. The optimal solution is found in two steps, optimization of the PS factor for given TA and then optimization of the TA factor using the conditionally optimized PS factor given in a closed-form. To reduce the complexity of the optimal method, we next propose a suboptimal method using a fixed TA determined by the transmission rate only and a fixed PS ffactor given by a function of the average power of the UAV-to-destination channel. The outage probability of the proposed method is analyzed in a generalized UAV channel model including path-loss, shadowing, and Nakagami-m fading, which is shown to agree with the simulation results and is close to the optimal performance. In addition, the optimal UAV position is investigated in various channel environments, which reveals that the optimal altitude depends on the deployment scenarios and the optimal ground position is the center-point between the source and destination in general.
6 June 2025 in Journal of Electrical Systems and Information Technology
In this paper, a low mutual coupling multiple-input and multiple-output (MIMO) antenna design is suggested for 5G applications. It consists of 1 × 2 array slotted E-shaped components positioned in the center of the substrate microstrip patch antenna profile. The substrate used is a Rogers RT-5880, which has a thickness of 0.254 mm and a dielectric constant of 2.2 along with a loss tangent of 0.0009. The frequency range that the proposed MIMO antenna arrays span, 37 GHz, is designated for millimeter-wave mobile applications in 5G. By adopting a defective ground structure (DGS), the mutual interaction between the antenna elements is reduced. Each antenna element is positioned one row ahead of the other. The gain of the suggested antenna array is 7.441 dBi, but using DGS, it increases that gain to 7.884 dBi. It is found that the suggested antenna array's radiation efficiency is nearly 90% within the intended operational frequency range. Performance measures for the proposed MIMO antenna, including diversity gain (DG) and envelope correlation coefficient (ECC), are observed and are determined below the standard threshold. Finally, a comparison between the suggested design and previous research is shown, where the suggested antenna is performed better in various performance metrics.
31 March 2024 in Journal of Advanced Engineering and Computation
This paper presents the design and simulation of an efficient multiple input multiple output (MIMO) antenna array for 5G millimeter-wave (mm-wave) mobile applications. With a dielectric constant of 2.2 and a loss tangent of 0.0009, the substrate employed is a Rogers RT5880 that is 0.254 mm thick. The 37 GHz frequency spectrum, reserved for millimeter-wave mobile applications for 5G, is covered by the proposed MIMO antenna arrays. The single antenna element has a gain of 6.44 dBi, which is increased to 7.89 dBi with a two-element array configuration and 10.88 dBi with a four-element array configuration. The proposed MIMO antenna array performance metrics—including reflection coefficient, VSWR, radiation efficiency, and gain—are seen and discovered to be below the accepted threshold. In the desired operating frequency band, it is noticed that more than 85% of the proposed MIMO antenna array's radiation efficiency is achieved. According to simulation findings, the proposed design may be potentially feasible for mobile applications using millimeter waves in the 5G network.
7 December 2023 in e-Prime - Advances in Electrical Engineering, Electronics and Energy
31 March 2023 in Journal of Advanced Engineering and Computation
Power consumption by telecommunication industrial loads is increasing day by day as the user of this technology is on the rise. Telecommunication base station towers are consuming twice or more energy than in the past for the implementation of high-capacity devices to serve more users. As a result, there is an extra power requirement for the telecommunication loads which can cause an inadequate power supply and lead to the implementation of additional infrastructure in the power industry. Powering these resources will demand more energy production and introduce various types of new problems in the grid network. The impact analysis of the effect of this extra demand in a regular network system has great interest. Also, most of the base stations are equipped with a backup battery as an essential need in third-world country grids and contribute a portion of the load demand of a power distribution system. All telecommunication industrial towers are considered under industrial load and have a special industrial tariff imposed by the power supply authority. This paper utilizes the optimal power flow method to calculate a proposed schedule base demand-side management system adopted to shift the pattern of charging batteries along with temperature control loads in the telecommunication towers and outlines an analytical study on a test power grid network. To determine the best electricity flow, generation, and locational marginal prices for each hour, an algorithm is created. Following careful evaluation of the appliance status, the constraint and condition are then applied to the load curve. This study indicates there is energy-saving and both supplier and consumer sides can minimize the operation cost. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium provided the original work is properly cited.