Raudhah Ahmadi

Raudhah Ahmadi

Auto-generated profile, based on publicly available information

Raudhah Ahmadi

Department of Civil Engineering, Faculty of Engineering, Universiti Malaysia Sarawak, Kota Samarahan, 94300, Sarawak, Malaysia

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 September 2016 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
RAR. Ahmadi
R. Ahmadi
NZN. Zainudin
N. Zainudin
III. Ismail
I. Ismail
MMM. A. Mannan
M. A. Mannan
AAA. S. Z. Abidin
A. S. Z. Abidin
Micro fine sized palm oil fuel ash (POFA) is a new supplementary cementitious material that can increase the strength, durability, and workability of concrete. However, production of this material incurs high cost and is not practical for the construction industry. This paper investigates a simple methodology of producing micro fine sized POFA by means of a laboratory scale wind tunnel system. The raw POFA obtained from an oil palm factory is first calcined to remove carbon residue and then grinded in Los Angeles abrasion machine. The grinded POFA is then blown in the fabricated wind tunnel system for separation into different ranges of particle sizes. The physical, morphological, and chemical properties of the micro fine sized POFA were then investigated using Laser Particle Size Analyser (PSA), nitrogen sorption, and Scanning Electron Microscopy with Energy Dispersive X-Ray (SEM-EDX). A total of 32.1% micro fine sized POFA were collected from each sample blown, with the size range of 1–10 micrometers. The devised laboratory scale of wind tunnel production system is successful in producing micro fine sized POFA and, with modifications, this system is envisaged applicable to be used to commercialize micro fine sized POFA production for the construction industry.

1 March 2021 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SBSalmia Binti Beddu
Salmia Binti Beddu
MZMahyun Zainoodin
Mahyun Zainoodin
ABAmalina Basri
Amalina Basri
Zarina ItamZarina Itam
Zarina Itam
RARaudhah Ahmadi
Raudhah Ahmadi
TMTeh Sabariah Binti Abd Manan
Teh Sabariah Binti Abd Manan
Coal Combustion Waste (CCW) fly ash, main component of coal ash waste generated at the Coal-Fired Power Plant throughout the year that causes the presents of toxic metals in the ash. Hence, pose significant health threats towards humans and environment. Cenosphere is a coal combustion by-product obtained from fly ash in boilers of coal fired power plants. The properties of cenosphere including spherical, lightweight, good thermal stability, chemical proof, heat resistance making it to have improved insulation. The aim of this research was to investigate the potential of cenospheres production from three different coal fired power plants in Malaysia namely Jimah, Kapar and Manjung. The wet method was used for cenospheres separation from the fly ash. The percentages of cenospheres ranged from 1 to 1.2% of every 1000 gram of fly ash. The mean sizes were 95.86μm 88.64μm, 49.04μm for Jimah, Kapar and Manjung respectively. Cenosphere evacuated by utilizing water as a medium, it will expend a lot of water and lead to water contamination cause of leaching of toxic material while extracting the cenosphere from fly ash. Nevertheless, any health and environmental impacts from the value-added physical application of cenospheres in civil engineering materials must be screened via strict monitoring and legislated guidelines.

30 June 2022 in Journal of Sustainability Science and Management
Verified
Journal Article
Closed access
USUniversiti Malaysia Sarawak
Universiti Malaysia Sarawak
RARaudhah Ahmadi
Raudhah Ahmadi
MSMohd Syukry Saiful
Mohd Syukry Saiful
IIIdawati Ismail
Idawati Ismail
MMMohamad Abdul Mannan
Mohamad Abdul Mannan
NSNorsuzailina Mohamed Sutan
Norsuzailina Mohamed Sutan
The performance of Fibre Reinforced Mortar (FRM) mixed with microfine size Palm Oil Fuel Ash was investigated in this study (POFA). The ideal volume of POFA and fibre in the mixed mortar is calculated in order to generate a cost-effective high-strength mortar with increased ductility. In this experimental investigation the polypropylene fibre used ranged from 0 kg/m3 to 20 kg/m3 and the replacement of cement with microfine POFA content of 0% and 40% (optimum) was studied. The mechanical properties of fibre reinforced masonry in the presence of the POFA was tested using compressive strength, flexural and split tensile tests. The surface morphology of the fibre reinforced mortar was studied using scanning electron microscopy (SEM) which showed the good fibre-mortar bond in the morphology of the samples at 7 and 28 days. From the compressive strength results, FRM tester contains 40% microfine POFA as a replacement against cement mixed with 10 kg/m3 of polypropylene fibre is optimum and achieved compressive strength up to 79.5 MPa at the 56th day of curing. Ductility ratio up to 13.3 was achieved from the flexural test for FRM sample with 15 kg/m3 polypropylene fibres. The high strength FRM with inclusion of POFA as supplementary cementitious material had the potential to become a new sustainable material in construction.

8 September 2021 in Defect and Diffusion Forum
Verified
Journal Article
Closed access
PDF file
SRSharon Robert
Sharon Robert
IIIdawati Ismail
Idawati Ismail
RARaudhah Ahmadi
Raudhah Ahmadi
NSNur Amalina Shairah Abdul Samat
Nur Amalina Shairah Abdul Samat
In cement industry, the emissions of greenhouse gases specifically CO2 from the clinker production led to the need of alternative binders. Geopolymer binder whose precursors are sourced from industrial by-products such as fly ash that are rich is silica and alumina has been studied extensively in the past decades. Chloride attack is one of the threats to concrete structures. Analysis at microstructural level needs to be studied carefully before this binder can be used with confidence. This study attempts to compare the properties of fly ash geopolymer binder when exposed in water and chloride solution. Fly ash geopolymer pastes were prepared using 12M sodium hydroxide (NaOH) as activator. The pastes were tested under two separate curing conditions, i.e in ambient and in distilled water. Compressive strength test along with microstructure properties of samples cured at 7, 14 and 28 days were conducted via Universal testing machine, Fourier Transform Infra-Red (FTIR) spectroscopy and Scanning Electron Microscope with Energy-dispersive X-ray (SEM-EDX). After 28 days of curing, these samples were immersed in 10% sodium chloride (NaCl) solution for another 56 days. Samples cured in ambient condition showed better mechanical performance than those in distilled water. Their differences in compressive strength were also seen consistent with the FTIR results. Samples exposed to NaCl and distilled water showed similar mechanical performance and microstructural properties. Based on SEM-EDX analysis, samples cured in ambient were rich in silica and alumina while the intensity of these compounds were observed to reduce when exposed to distilled water. Samples cured in ambient showed stronger intensity of Si/Al gel as compared to samples exposed to chloride environment and distilled water and these were consistent with the compressive strength results obtained. When immersed in water, concentration gradient changes in the liquid phases, leading to ions diffusion and causing decrement in strength and durability of the solids in fly ash geopolymer.

31 October 2025 in Journal of Applied Science & Process Engineering
Verified
Journal Article
Open access
NRNur Hisyam Ramli
Nur Hisyam Ramli
STSiti Noor Linda Taib
Siti Noor Linda Taib
NSNorazzlina M. Sa'DOn
Norazzlina M. Sa'DOn
DIDayangku Salma Awang Ismail
Dayangku Salma Awang Ismail
RARaudhah Ahmadi
Raudhah Ahmadi
NRNazeri Abdul Rahman
Nazeri Abdul Rahman
Landslides are the third most frequent form of natural disaster in Malaysia, following floods and storms. It can cause significant damage to anything in its path, depending on the size and velocity of its debris. Due to the danger that it poses, determining the susceptibility of an area to landslides is a crucial step in risk mitigation. Landslide occurrences are dependent on the numerous environmental variables, which can provide information on the level of susceptibility of other locations with similar variables. To quantify the significance of each variable to landslide occurrence, a supervised Machine Learning model – an Artificial Neural Network was developed for this study. Furthermore, landslide occurrences have been associated with the disturbance of natural slopes to accommodate development, which was the main reason behind the selection of Western Sarawak as the area of interest in this study. The model was developed to understand and make landslide susceptibility predictions based on aspect, curvature, elevation, lithology type, rainfall intensity, slope angle, soil type, and TWI. Evaluating the area under the curve score and recall for the model revealed that, based on the available inputs, the model performed well with a score of 1 and 0.99, respectively.