This paper presents a two-stage T-type hybrid five-level transformerless inverter (TLI) for grid-connected photovoltaic (PV) applications. The proposed T-type hybrid five-level inverter and its level-shifted pulse width modulation (LSPWM) scheme offers: (i) Reduced leakage current by eliminating the high frequency variations and sudden transitions in the voltage across PV parasitic capacitance (CPV), (ii) A path for the negative current in all the modes of operation under unity and non-unity power factor conditions of the grid without degrading the waveform quality. Moreover, in this paper the proposed inverter is integrated with a traditional three-level boost converter (3LBC) for boosting the lower PV voltage to higher DC-link voltage and also to extract maximum power from the PV source. The 3LBC provides high efficiency and reduced input inductor size for the same power rating over the conventional boost converter. Simulation results of the proposed system are presented using MATLAB software, and a 500 W experimental prototype is constructed and tested in the laboratory to validate the feasibility of the proposed configuration. Finally, a comparison of the proposed inverter with other five-level TLI topologies is presented to highlight its merits.
5 August 2019 in IEEE Transactions on Industry Applications
Multi-Level Inverters (MLIs) are playing a pivotal role in the power sector with potential applications such as interfacing renewable energy sources with the grid and several industrial drive applications. MLIs with a smaller number of switching devices are more promising due to their compact size, reduced cost and higher efficiency compared to their traditional counterparts. This paper, therefore, presents a new three-phase seven-level inverter. This topology is a combination of two cascade-connected two-level Voltage Source Inverters (VSIs) and H-bridge cells with flying capacitors (FCs). This paper presents the operating principle and the balancing technique for the DC-link capacitors and FCs. The generation of various output voltage levels and the limitation of the Sinusoidal Pulse Width Modulation (SPWM) control for FC voltage balancing is also presented. The number of components in the proposed circuit configuration and their voltage ratings are considerably lower compared to the recently proposed topologies. The behavior of the proposed circuit configuration is first assessed with simulation studies and is then tested with a laboratory prototype. The simulation and experimental results validate the effectiveness of the proposed topology and the voltage balancing technique.
2 June 2020 in IEEE Transactions on Industry Applications
Transformerless inverters (TLIs) are competently accepted for Photovoltaic (PV) applications because of their high efficiency, reduced size, lower cost. But, in the absence of a transformer there exist a galvanic connection between PV array to ground and it results in the flow of hazardous leakage current. Several TLI topologies have been proposed in the literature with decoupling circuits to reduce the leakage current. Among those H5, Heric, and H6 topologies are the most popular and widely accepted TLIs. Nevertheless, the effect of switch junction capacitances was not considered in the common-mode voltage (CMV) analysis which inevitably causes excess leakage current. Also, reactive power capability cannot be accomplished with traditional pulse-width modulation (PWM) schemes due to the absence of a bi-directional current path during the freewheeling period. Therefore, in this paper, a bi-directional clamping (BDC) based H5, Heric, and H6 TLI topologies are proposed with improved PWM schemes. BDC branch reduces the leakage current by clamping the inverter terminal voltages to half of the DC-link voltage during the freewheeling period and the improved PWM schemes ensure bi-directional current path while operating in negative power region. The performance of both traditional and proposed topologies are tested with MATLAB simulations and further justified with experimental results.
1 December 2011 in IEEE Transactions on Power Electronics
The private power producers are increasing rapidly to meet rising load demand in domestic, commercial, and industrial sectors. In this scenario, the distributed generation systems (DGs) play an important role over fossil fuel generation. Among different distributed generation technologies such as fuel cell, wind power, and solar; the fuel-cell-based distributed generation is becoming more popular due to its high efficiency, cleanliness, modularity, and cost effectiveness. The development of a suitable power electronic interface and control schemes, therefore, play vital role in regulating fuel-cell voltage, both under steady and transient conditions. This paper, therefore, presents a DSP-controlled single stage power electronic interface for fuel-cell-based generation intended for residential/grid connected applications. The presented scheme generates pulse width modulation (PWM) control signals using TMS320F2812 DSP controller interfaced with MATLAB/Simulink model. A comprehensive simulink based model of the scheme is evolved and discussed. The experimental results are presented for varying loads and transient conditions.
30 October 2018 in International Journal of Circuit Theory and Applications