Alexander T. Bikmeyev

Alexander T. Bikmeyev

Auto-generated profile, based on publicly available information

Alexander T. Bikmeyev

Ufa State Aviation Technical University, Ufa, Russia

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 November 2014
Verified
Conference Paper
Closed access
PDF file
KSK. Savvakis
K. Savvakis
MPM. Petousis
M. Petousis
AVAchilles Vairis
Achilles Vairis
NVN. Vidakis
N. Vidakis
ABA. T. Bikmeyev
A. T. Bikmeyev
Acrylonitrile–butadiene–styrene (ABS) is a popular engineering thermoplastic and it is the most common material used in fused deposition modeling (FDM) technology. This technology is nowadays used for the production of prototypes and functional parts as well. It is therefore critical to know the mechanical properties of these parts, which, is as expected different from their nominal values. In this work the tensile strength of parts build with the FDM process is measured. ABS and ABS plus parts were built with different building parameters and were tested according to the ASTM D638-02a standard on a Schenk Trebel Co. tensile test machine. It was found that the building direction does not significantly influence the tensile strength of the parts, although the parts were anisotropic, as expected. Parts build with larger layer thickness showed lower tensile strength. The average deviation between nominal and experimental tensile strength was about 15% for the ABS and about 42% for the ABS plus material. The ABS plus showed on average 9% higher strength than ABS.

1 February 2001 in Journal of Magnetism and Magnetic Materials
Verified
Journal Article
Closed access
MSM.A. Shamsutdinov
M.A. Shamsutdinov
ABA.T. Bikmeyev
A.T. Bikmeyev
BFB.N. Filippov
B.N. Filippov
AKA.A. Khalfina
A.A. Khalfina

27 February 2025 in Bulletin of Russian State Medical University
Verified
Journal Article
Open access
ABAr Bilyalov
Ar Bilyalov
SPSvetlana Piatnitskaia
Svetlana Piatnitskaia
GRGa Rafikova
Ga Rafikova
VAVn Akbashev
Vn Akbashev
ABAt Bikmeyev
At Bikmeyev
ATAa Tikhonov
Aa Tikhonov
The choice of the sterilization method for ceramic implants is critically important, as it can affect the chemical and physico-mechanical properties of the material and its biocompatibility. Higher cytotoxicity, which is a possible side effect of sterilization, hinders osseointegration. This study aimed to determine the cytotoxicity of porous ceramic samples after sterilization using the most common methods. Samples of hydroxyapatite (HA), tricalcium phosphate (TCP), and aluminum oxide (AO) were prepared by stereolithography, and bone allograph samples were made using the DLP method. The annealing lasted for 4 hours, with a peak temperature of 800 °C and the temperature increment of 3 °C per minute; the sintering temperature was up to 1200 °C. We used the following sterilization methods: autoclaving at 1 atmosphere, 120 °C, for 45 minutes; radiation sterilization, 25 seconds with an absorbed dose of 25 kGy; plasma peroxide sterilization, 42 minutes; dry heat sterilization at 180 °C, for 60 minutes. Cytotoxicity was determined with the help of an MTT assay (24-hour exposure in a CO2 incubator). The results of the study: for HA, high porosity means growth of values in transition from autoclaving (0.1115) to plasma peroxide sterilization (0.2023). Medium and low porosity show similar results, with peaks in dry-heat sterilization (0.4954 and 0.4505). As for for AO, it exhibited high viability when subjected to this method. The TCP samples have shown stable results, but their low-porosity variation had the values growing after autoclaving (0.078 to 0.182, dry-heat sterilization). The study forms the basis for optimizing the ceramic implants manufacturing technology and sterilization methods to ensure their high biocompatibility.

1 December 2014 in Journal of Engineering Science and Technology Review
Verified
Journal Article
Closed access
AYA. Yamileva
A. Yamileva
ACA. Chukalova
A. Chukalova
ABA. Bikmeyev
A. Bikmeyev
RGR. Gazizov
R. Gazizov

1 September 2012 in Journal of Engineering Science and Technology Review
Verified
Journal Article
Closed access
KUKarl Marx Str. Usatu
Karl Marx Str. Usatu
SIS. V. Ivanov
S. V. Ivanov
SPS. I. Perepelica
S. I. Perepelica
F«Ferin Str. Jsc «Umpo»
Ferin Str. Jsc «Umpo»
ABA. T. Bikmeyev
A. T. Bikmeyev

15 November 2013
Verified
Conference Paper
Closed access
PDF file
ABAlexander T. Bikmeyev
Alexander T. Bikmeyev
RGRafail K. Gazizov
Rafail K. Gazizov
AVAchilles Vairis
Achilles Vairis
AYAlfiya M. Yamileva
Alfiya M. Yamileva
This paper describes the results of the mathematical and computer modeling efforts of heat generation in the contact area of a moving object on an infinite plane with friction. The distribution of contact pressure with a linear approximation was obtained. The heat equations for a nonlinear volume heat source were solved. It is shown, that at the initial stages of the linear friction welding (LFW) process temperature distribution is non-elliptical with two hot spots appearing near the edges of the moving specimen. Then as the process progresses these two spots expand and move to the center of the specimen. The results of the mathematical and the numerical modeling in ANSYS APDL software are in good quantitative agreement.