Barbara Michorczyk

Barbara Michorczyk

Auto-generated profile, based on publicly available information

Barbara Michorczyk

Cracow University of Technology, Faculty of Chemical Engineering and Technology, Warszawska 24, 31-155 Kraków, Poland

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2017 in Nanomaterials
Verified
Journal Article
Open access
PDF file
AWAdam Węgrzyniak
Adam Węgrzyniak
SJSebastian Jarczewski
Sebastian Jarczewski
AWAdam Węgrzynowicz
Adam Węgrzynowicz
BMBarbara Michorczyk
Barbara Michorczyk
Piotr KuśtrowskiPiotr Kuśtrowski
Piotr Kuśtrowski
PMPior Michorczyk
Pior Michorczyk
Mesoporous alumina with narrow pore size distribution centered in the range of 4.4–5.0 nm and with a specific surface area as high as 270 m2·g−1 was prepared via the nanocasting approach using a CMK-3 carbon replica as a hard template. Based on this support, a series of catalysts containing 1, 5, 10, 20 and 30 wt % of chromium was prepared by incipient wetness impregnation, characterized, and studied in the dehydrogenation of propane to propene (PDH). Cr species in three oxidation states—Cr(III), Cr(V) and Cr(VI)—were found on the oxidized surface of the catalysts. The concentration of these species varied with the total Cr loading. Temperature-programmed reduction (H2-TPR) and UV-Vis diffuse reflectance spectroscopy (UV-Vis-DRS) studies revealed that Cr(VI) species dominated at the lowest Cr content. An increase in the Cr loading resulted in an appearance of an increasing amount of Cr(III) oxide. UV-Vis-DRS measurements performed in situ during the PDH process showed that at the beginning of the catalytic test Cr(VI) species were reduced to Cr(III) redox species. A crucial role of the redox species in the PDH process over the catalysts with the low Cr content was confirmed. The stability test for the catalyst containing 20 wt % of Cr showed that this sample exhibited the reproducible catalytic performance after the first four regeneration–dehydrogenation cycles. Moreover, this catalyst had higher resistance on deactivation during the PDH process as compared to the reference catalyst with the same Cr loading, but was supported on commercially available alumina.

8 November 2017 in Catalysis Science & Technology
Verified
Journal Article
Closed access
PDF file
AWA. WęGrzyniak
A. WęGrzyniak
ARAnna Rokicinska
Anna Rokicinska
EHE. HęDrzak
E. HęDrzak
BMB. Michorczyk
B. Michorczyk
KZK. Zeńczak-Tomera
K. Zeńczak-Tomera
PMPior Michorczyk
Pior Michorczyk
Ordered mesoporous Cr–Zr–O and Cr–Zr–K–O catalysts were prepared by nanocasting using a CMK-3 carbon replica as a hard template. The synthesized oxide nanoreplicas had a uniform pore-size distribution centered in the range of 5.5–6.5 nm and specific surface areas of 123–164 m2 g−1. Results of physicochemical characterization (UV-vis DRS, EPR, XRD, XPS and H2-TPR) revealed that chromium species were stabilized in +3, +5 and +6 oxidation states in all samples. The developed materials exhibited excellent catalytic performance and much higher resistance to deactivation during the process of dehydrogenation of propane to propene in comparison with a material prepared without the CMK-3 hard template assistance. Potassium doping (0.2, 0.5 or 1.0 wt%) of the catalyst with a Zr/Cr atomic ratio of 5 enhanced the selectivity to propene and resistance to coke deposition.

31 May 2025 in ChemCatChem
Verified
Journal Article
Closed access
BMBarbara Michorczyk
Barbara Michorczyk
MKMonika Kralka‐Muzyk
Monika Kralka‐Muzyk
MKMagdalena Król
Magdalena Król
Adam Marian WęgrzynowiczAdam Marian Węgrzynowicz
Adam Marian Węgrzynowicz
NSNatalia Sobuś
Natalia Sobuś
PMPior Michorczyk
Pior Michorczyk

11 July 2025 in Chemical and Process Engineering: New Frontiers
Verified
Journal Article
Closed access
PDF file
BMBarbara Michorczyk
Barbara Michorczyk
DBDominika Baran
Dominika Baran
A series of inexpensive, stable, and environmentally friendly iron pigments was synthesized based on zeolite and clay minerals. For the synthesis of pigments, zeolite – clinoptilolite and clay minerals: bentonite and kaolin were used and as a source of iron ions – iron chloride. The influence of the type of clay minerals/zeolite used and the preparation method on the color of the obtained pigments and the resistance of the produced material to factors such as: UV radiation, organic solvents, alkalis and acids were studied. The use of different synthesis methods and various clay minerals or zeolite for the preparation of iron-based pigments enabled the formation of a wide range of colors, varying from beige and red to different shades of brown. The non-toxicity and good stability of the obtained pigments combined with the low cost of their production make them have great potential for use in many areas, such as ceramics, painting and others.