8 May 2024 in ACS Applied Materials & Interfaces
Layered oxides constitute one of the most promising cathode materials classes for large-scale sodium-ion batteries because of their high specific capacity, scalable synthesis, and low cost. However, their practical use is limited by their low energy density, physicochemical instability, and poor cycling stability. Aiming to mitigate these shortcomings, in this work, we synthesized polycrystalline (PC) and single-crystal (SC) P2-type Na0.67-δMn0.67Ni0.33O2 (NMNO) cathode materials through a solid-state route and evaluated their physicochemical and electrochemical performance. The SC-NMNO cathode with a large mean primary particle size (D50) of 12.7 μm was found to exhibit high cycling stability leading to 47% higher capacity retention than PC-NMNO after 175 cycles at 1C rate in the potential window 4.2-1.5 V. This could be attributed to the effective mitigation of parasitic side reactions at the electrode-electrolyte interface and suppressed intergranular cracking induced by anisotropic volume changes. This is confirmed by the lower volume variation of SC-NMNO (ΔV ∼ 1.0%) compared to PC-NMNO (ΔV ∼ 1.4%) upon charging to 4.2 V. Additionally, the SC-NMNO cathode displayed slightly higher thermal stability compared to PC-NMNO. Both cathodes exhibited good chemical stability against air and water exposure, thus enabling material storage/handling in the ambient atmosphere as well as making them suitable for aqueous processing. In this regard, PC-NMNO was investigated with two low-cost aqueous binders, carboxymethyl cellulose, and sodium trimetaphosphate, which exhibited higher binding strength and displayed excellent electrochemical performance compared to PVDF, which could potentially lead to significant cost reduction in electrode manufacturing.
24 September 2023 in Advanced Energy Materials
A key challenge for practical magnesium–sulfur (Mg–S) batteries is to overcome the sluggish conversion kinetics of sulfur cathodes, achieving a high energy density and long‐lasting battery life. To address this issue, a doping strategy is demonstrated in a model Ketjenblack sulfur (KBS) cathode by introducing selenium with a high electronic conductivity. This leads to a significantly enhanced charge transfer in the resultant KBS1−xSex cathodes, giving rise to a higher S utilization and less polysulfide dissolution. Compared to the bare S cathode, the S‐Se composite cathodes exhibit a higher capacity, smaller overpotentials, and improved efficiency, serving as better benchmark compounds for high‐performance Mg–S batteries. First principles calculations reveal a charge transport mechanism via electron polaron diffusion in the redox end‐products, that enhances the reaction kinetics. By suppressing polysulfide dissolution in the electrolyte, the use of the KBS1−xSex cathodes also enables a more uniform anode reaction, and thereby significantly extends the cyclability of the cells. To improve the performance, further efforts are made by implementing a Mo6S8 modified separator into the cell. With an optimized cathode composition of KBS0.86Se0.14, the cell applying modified separator shows an improvement of capacity retention by >50% after 200 cycles.
18 October 2024 in Advanced Energy Materials
Non‐trivial relationships link individual materials properties to device‐level performance. Device optimization therefore calls for new automation approaches beyond the laboratory bench with tight integration of different research methods. This study demonstrates a Materials Acceleration Platform (MAP) in the field of battery research based on the problem‐agnostic Fast INtention‐Agnostic LEarning Server (FINALES) framework, which integrates simulations and physical experiments while leaving the active control of the hardware and software resources executing experiments or simulations with the partners running the respective units. This decentralization of control is a distinctive feature of MAPs using the FINALES framework. The connected capabilities entail the formulation and characterization of electrolytes, cell assembly and testing, early lifetime prediction, and ontology‐mapped data storage provided by institutions distributed across Europe. The infrastructure is used to optimize the ionic conductivity of electrolytes and the End Of Life (EOL) of lithium‐ion coin cells by varying the electrolyte formulation. Trends in ionic conductivity are rediscovered and the effect of the electrolyte formulation on the EOL is investigated. Further, the capability of this MAP to bridge diverse research modalities, scales, and institutions enabling system‐level investigations under asynchronous conditions while handling concurrent workflows on the material‐ and system‐level is shown, demonstrating true intention‐agnosticism.
19 January 2023 in Scientific Data
Electrolytes are considered crucial for the performance of batteries, and therefore indispensable for future energy storage research. This paper presents data that describes the effect of the electrolyte composition on the ionic conductivity. In particular, the data focuses on electrolytes composed of ethylene carbonate (EC), propylene carbonate (PC), ethyl methyl carbonate (EMC), and lithium hexafluorophosphate (LiPF6). The mass ratio of EC to PC was varied, while keeping the mass ratio of (EC + PC) and EMC at fixed values of 3:7 and 1:1. The conducting salt concentration was also varied during the study. Conductivity data was obtained from electrochemical impedance spectroscopy (EIS) measurements at various temperatures. Based on the thus obtained temperature series, the activation energy for ionic conduction was determined during the analysis. The data is presented here in a machine-readable format and includes a Python package for analyzing temperature series of electrolyte conductivity according to the Arrhenius equation and EIS data. The data may be useful e.g. for the training of machine learning models or for reference prior to experiments.
22 April 2024 in ChemCatChem
Stimulated by the increasing interest in ion adsorption effects on electrocatalytic reactions and by recent more detailed reports on the potential dependent adlayer structures formed on Ru(0001) in pure HClO4 and H2SO4 electrolytes, we revisited the oxygen reduction reaction (ORR) on structurally well‐defined Ru(0001) single crystal surfaces prepared under ultrahigh vacuum conditions. We demonstrate that the complex, potential‐dependent activity both for the ORR and for H2O2 formation is closely related to potential‐dependent changes in the composition and structure of the adlayer. Our results demonstrate the enormous effects adsorbed species can have on the ORR reaction characteristics, either by surface blocking, e. g., by (co‐)adsorbed bisulfate species, or by participation in the reaction, e. g., by *H transfer from adsorbed H or OH to O2. The comparison with results obtained on polycrystalline Ru, which differ significantly from Ru(0001) data, furthermore underlines the importance of using structurally well‐defined surfaces as a reference system for future theoretical studies.
8 March 2025 in Small Structures
The Patrónite vanadium tetrasulfide (VS4) follows a simultaneous cationic and anionic redox (SCAR) mechanism in magnesium batteries, which renders a delocalized electronic structure for fast kinetics and meanwhile enables multielectron reactions for delivering high capacity. In contrast to most research that focuses on the hydrothermal route resulting in VS4 nanoparticles, herein a more industrially relevant synthesis route is targeted, utilizing a solid‐state approach leading to micron‐sized VS4. The obtained 2 × 10 μm VS4 needles show good water/air stability, allowing an environmentally friendly coatings procedure using polyvinylpyrrolidon binder in isopropanol. Electrochemical investigation shows that the micron‐sized VS4 cathode delivers a maximum capacity of 420 mAh g−1 in a tetrakis(hexafluoroisopropyloxy)borate (Mg[B(hfip)4]2)‐based electrolyte, however suffers from fast capacity fading and overcharging. Targeting these issues, a concentrated Mg[B(hfip)4]2 electrolyte in bis(2‐methoxyethyl)ether is applied, which enables stable cycling for 300 cycles at the expense of a reduced capacity. Multimodal characterizations confirm a reversible SCAR mechanism of VS4 during cycling. However, pulverization of the electrode and fragmentation of the VS4 backbones are evident, leading to the leakage of active material into electrolyte and causing capacity decay. To avoid active material loss, crystal engineering or surface protection strategies should be developed toward practical Mg batteries.