A polarization reconfigurable metasurface wideband antenna with dual polarized and a low radar cross section (RCS) is presented. The antenna employs a diode positioned between two transmission lines to control the current direction and a resistor on a defected-ground branch to manage phase shifts, enabling seamless transitions between circular polarization (CP) and linear polarization (LP). The elliptical metasurface design contributes to a reduced RCS. The design results are verified through measurement, showing an impedance bandwidth (IBW) of 49.1%, an axial ratio bandwidth (ARBW) of 23.2% for the diode is OFF, an IBW of 36.4% for the diode is ON, the IBW of the connected resistor is 40.7%, and the peak gains for the three states are 6.4 dBi, 4.4 dBi, and 4.2 dBi, respectively. The metasurface achieves a low RCS bandwidth ranging from 2 GHz to 24 GHz, showing a 6 dBsm reduction in RCS from 4.9 GHz to 19.7 GHz, which corresponds to a 120.3% decrease compared to a PEC plate.
Synthetic aperture radar (SAR) images are often disturbed by speckle noise, making SAR image interpretation tasks more difficult. Therefore, speckle suppression becomes a pre-processing step. In recent years, approaches based on convolutional neural network (CNN) achieved good results in synthetic aperture radar (SAR) images despeckling. However, these CNN-based SAR images despeckling approaches usually require large computational resources, especially in the case of huge training data. In this paper, we proposed a SAR image despeckling method using a CNN platform with a new learnable spatial activation function, which required significantly fewer network parameters without incurring any degradation in performance over the state-of-the-art despeckling methods. Specifically, we redefined the rectified linear units (ReLU) function by adding a convolutional kernel to obtain the weight map of each pixel, making the activation function learnable. Meanwhile, we designed several experiments to demonstrate the advantages of our method. In total, 400 images from Google Earth comprising various scenes were selected as a training set in addition to 10 Google Earth images including athletic field, buildings, beach, and bridges as a test set, which achieved good despeckling effects in both visual and index results (peak signal to noise ratio (PSNR): 26.37 ± 2.68 and structural similarity index (SSIM): 0.83 ± 0.07 for different speckle noise levels). Extensive experiments were performed on synthetic and real SAR images to demonstrate the effectiveness of the proposed method, which proved to have a superior despeckling effect and higher ENL magnitudes than the existing methods. Our method was applied to coniferous forest, broad-leaved forest, and conifer broad-leaved mixed forest and proved to have a good despeckling effect (PSNR: 23.84 ± 1.09 and SSIM: 0.79 ± 0.02). Our method presents a robust framework inspired by the deep learning technology that realizes the speckle noise suppression for various remote sensing images.
2 October 2024 in IET Microwaves, Antennas & Propagation
A low‐profile circularly polarised (CP) metasurface antenna is proposed, utilising characteristic mode analysis (CMA). The antenna design features a two‐layer laminated substrate, a 4×4 Butterfly‐shaped metasurface, a rectangular slot, an irregular transmission line, and a ground plane. The metasurface is analysed using mode significance (MS), characteristic angle (CA), and characteristic current to determine the resonance bandwidth and CA resonance points, which exhibit a near 90° difference. At the intersection of the two MS modes, their CAs differ by nearly 90°, and their far‐field radiation directions align, indicating the potential for achieving circular polarisation at the desired frequency. The integration of the metasurface with the slot antenna is simulated to validate the CMA findings. Additionally, the CP bandwidth is enhanced by modifying the transmission line branches. Measurement of the fabricated antenna reveals an impedance bandwidth (IBW) of 27.4%, a 3‐dB axial ratio bandwidth (ARBW) of 10.1%, and a peak gain of 6.9 dBic at 4.4 GHz. Compared to the design without branches, IBW and ARBW have increased by 10% and 7.3%, respectively.
27 March 2025 in International Journal of Circuit Theory and Applications