Anthony James Robinson

Anthony James Robinson

Auto-generated profile, based on publicly available information

Anthony James Robinson

Trinity Coll Dublin, Dept Mech & Mfg Engn, Parsons Bldg, Dublin, Ireland

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 March 2017 in International Materials Reviews
Verified
Journal Article
Closed access
KRKafil M. Razeeb
Kafil M. Razeeb
EDEric Dalton
Eric Dalton
GCGraham Lawerence William Cross
Graham Lawerence William Cross
ARAnthony James Robinson
Anthony James Robinson
Packaging electronic devices is a growing challenge as device performance and power levels escalate. As device feature sizes decrease, ensuring reliable operation becomes a challenge. Ensuring effective heat transfer from an integrated circuit and its heat spreader to a heat sink is a vital step in meeting this challenge. The projected power density and junction-to-ambient thermal resistance for high-performance chips at the 14 nm generation are >100 Wcm−2 and <0.2 °CW−1, respectively. The main bottleneck in reducing the net thermal resistance are the thermal resistances of the thermal interface material (TIM). This review evaluates the current state of the art of TIMs. Here, the theory of thermal surface interaction will be addressed and the practicalities of the measurement techniques and the reliability of TIMs will be discussed. Furthermore, the next generation of TIMs will be discussed in terms of potential thermal solutions in the realisation of Internet of Things.

1 July 2013 in International Journal of Multiphase Flow
Verified
Journal Article
Closed access
AAA. Albadawi
A. Albadawi
DDD.B. Donoghue
D.B. Donoghue
ARA.J. Robinson
A.J. Robinson
DMD.B. Murray
D.B. Murray
YDY.M.C. Delauré
Y.M.C. Delauré

1 January 2013 in Applied Thermal Engineering
Verified
Journal Article
Closed access
JDJens Due
Jens Due
ARAnthony J. Robinson
Anthony J. Robinson

1 February 2010 in Applied Thermal Engineering
Verified
Journal Article
Open access
Hussam JouharaHussam Jouhara
Hussam Jouhara
ARAnthony J. Robinson
Anthony J. Robinson
Copyright © 2009 Elsevier Ltd. All rights reserved.An experimental investigation of the performance of thermosyphons charged with water as well as the dielectric heat transfer liquids FC-84, FC-77 and FC-3283 has been carried out. The copper thermosyphon was 200 mm long with an inner diameter of 6 mm, which can be considered quite small compared with the vast majority of thermosyphons reported in the open literature. The evaporator length was 40 mm and the condenser length was 60 mm which corresponds with what might be expected in compact heat exchangers. With water as the working fluid two fluid loadings were investigated, that being 0.6 ml and 1.8 ml, corresponding to approximately half filled and overfilled evaporator section in order to ensure combined pool boiling and thin film evaporation/boiling and pool boiling only conditions, respectively. For the Fluorinert™ liquids, only the higher fill volume was tested as the aim was to investigate pool boiling opposed to thin film evaporation. Generally, the water-charged thermosyphon evaporator and condenser heat transfer characteristics compared well with available predictive correlations and theories. The thermal performance of the water-charged thermosyphon also outperformed the other three working fluids in both the effective thermal resistance as well as maximum heat transport capabilities. Even so, FC-84, the lowest saturation temperature fluid tested, shows marginal improvement in the heat transfer at low operating temperatures. All of the tested Fluorinert™ liquids offer the advantage of being dielectric fluids, which may be better suited for sensitive electronics cooling applications and were all found to provide adequate thermal performance up to approximately 30–50 W after which liquid entrainment compromised their performance

1 October 2009 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Open access
Conor BuckleyConor Buckley
Conor Buckley
Stephen ThorpeStephen Thorpe
Stephen Thorpe
FOFergal J. O’bRien
Fergal J. O’bRien
ARAnthony J. Robinson
Anthony J. Robinson
DKDaniel Kelly
Daniel Kelly
Agarose hydrogels are commonly used for cartilage tissue engineering studies and to provide a three dimensional environment to investigate cellular mechanobiology. Interpreting the results of such studies requires accurate quantification of the mechanical properties of the hydrogel. There is significant variation in the reported mechanical properties of agarose hydrogels, and little is reported on the influence of factors associated with mixing these hydrogels with cell suspensions on their initial mechanical properties. The objective of this study was to determine the influence of agarose concentration, the cooling rate during gelation, the thermal history following gelation and the cell seeding density on the initial mechanical properties of agarose hydrogels. The average ramp modulus of 2% agarose gel in tension was 24.9 kPa (+/-1.7, n=10), compared with 55.6 kPa (+/-0.5, n=10) in compression. The average tensile equilibrium modulus was 39.7 kPa (+/-5.7, n=6), significantly higher than the compressive equilibrium modulus of 14.2 kPa (+/-1.6, n=10). The equilibrium and dynamic compressive modulus of agarose hydrogels were observed to reduce if maintained at 37 ( composite function)C following gelation compared with samples maintained at room temperature. Depending on the methodology used to encapsulate chondrocytes within agarose hydrogels, the equilibrium compressive modulus was found to be significantly higher for acellular 2% agarose gels compared with 2% agarose gels seeded at approximately 40 x 10(6) cells/mL. These results have important implications for interpreting the results of chondrocyte mechanobiology studies in agarose hydrogels.

1 January 2013 in Experimental Thermal and Fluid Science
Verified
Journal Article
Open access
SBSergio Di Bari
Sergio Di Bari
ARAnthony J. Robinson
Anthony J. Robinson