1 May 2017 in Magazine of Concrete Research
The interface between new concrete (overlay) and old concrete (substrate) plays an important role in the overall success of any repair. A good bond ensures long-term durability and monolithic action (i.e. the overlay contributes to both the stiffness and load-carrying capacity). Research has shown that the substrate roughness, which is highly dependent on the surface preparation method, has an influence on the interface bond strength, though there is no consensus on the extent of this effect. Thus, through a new bond test, an experimental study was conducted to evaluate the effect of substrate roughness on bond strength, also considering the effect of overlay strength. In addition, the possible consequence of roughness on interface ductility was evaluated. The results indicate an increase in bond strength with an increase in surface roughness, although the resulting increase in ductility with surface roughness was more pronounced. The strength of the overlay was also found to be an important parameter for smooth substrates or substrates with low roughness.
1 September 2019 in Cement and Concrete Composites
21 October 2020 in Materials and Structures
The continued interest in technological innovation in construction has greatly broadened the horizons of material science, developing a specific sector closely related to the recycling of waste products. This paper examines the thermal, mechanical and structural behaviour of an insulating light weight fibre reinforced concrete (ILWFRC), which is made by replacing natural sand and gravel with artificial aggregates resulting from the process of glass recycling. ILWFRC offers low density (approximately 650 kg/m3), excellent thermal characteristics (thermal conductivity 0.1 W/mK), a compressive strength similar to brick masonry (3.5 MPa) with low cement content (265 kg/m3) and stable post-cracking behaviour. The mechanical and physical properties of ILWFRC were employed for the construction of a full-scale infill wall (having dimensions of 2.9 × 2.6 × 0.2 m), which was experimentally studied under in-plane and out-of-plane actions. In-plane response showed a maximum lateral load of 359 kN at 1.5% drift, with a residual capacity of more than 75% at 4% drift. The subsequent out-of-plane test was performed up to failure with a maximum lateral load of 67 kN, corresponding to about 7 times the infill self-weight.
23 September 2016 in Key Engineering Materials
After more than fifty years from the opening of the largely discussed “Autostrada del Sole” Highway in 1964, the infrastructure system in Italy appears marked by the passing of time, similarly to what observed in several other countries worldwide. The great heterogeneity of the Italian landscape has determined a great variety of construction types, such as large span concrete bridges over the northern rivers and large arch concrete bridges over the valleys of the central region. Increment of vehicle traffic and new seismic regulations are setting new requirements to adapt the existing infrastructure, which should be otherwise replaced. Moreover, reinforced concrete (RC) aging and deterioration have led to structural and material degradation, including severe cracking and corrosion. Specialized materials such as High Performance Concrete (HPC) could represent a viable convenient solution for repairing, strengthening and retrofitting of RC structures as both structural capacity and durability can be refurbished. However, alongside high mechanical performance, HPC is characterized by a high cracking sensitivity at very early age, due to its high stiffness and shrinkage. Restrained shrinkage cracking, particularly significant in repaired structures where the existing concrete generates a considerable restraint against the free movement of the repair material, may represent a limit to the effective application of these materials. For this reason, shrinkage compatibility of HPC with the existing concrete substrate needs to be experimentally and numerically assessed. A study is herein presented where, based on experimental tests, different numerical models are developed and compared to assess and eventually minimize the risk of shrinkage cracking in bridge piers strengthened with HPC.
31 October 2018 in MATEC Web of Conferences
The increasing number of road infrastructures needing repair and retrofit is raising the problem of how to improve seismic behaviour for all those structures for which substitution is unlikely. This work deals with the application of a retrofitting technique for Reinforced Concrete (RC) elements based on the use of Ultra High Performance Fibre Reinforced Concrete (UHPFRC). A thin layer of UHPFRC, cast around an existing RC element, can both improve its structural performance and enhance its durability against environmental actions. This kind of rehabilitation intervention may represent, in many practical cases, a cost effective solution compared with the replacement of the entire structure. The aim of this paper is the definition of a reinforcement strategy and the presentation of a 1:4 scale laboratory test of a highway bridge pier reinforced with a 30 mm layer of UHPFRC.