31 October 2023 in Eastern-European Journal of Enterprise Technologies
A study of a model of a discrete-continuous type of impactor in the energy transfer phase during the impact of a striker and a tool is presented. The device is used to destroy rocks, in construction equipment, and in the oil industry. In the mathematical model, the tool is represented by a rod with a variable profile, and the striker is a discrete element with a consolidated mass. The presence of rigid and dissipative connections models the impact interaction. The motion of the interacting elements of the impactor is described by a system of differential equations linked by boundary and initial conditions. The model allows determining the parameters of influence on the characteristic of the shock pulse at variable resistance of the working medium. The force of impact of a discrete element and the contact end of the rod is represented as a power law dependent on the difference in displacements of the contacting elements. The finite difference method is used to solve the initial boundary value problem. The parameters of the difference scheme were determined through modelling problems and were as follows: time step (1, ..., 5)·10-5 s; length step – (0.1...0.3) of the tool length, and for the mixed scheme – within 0.5...0.8. It was found that the time of striker-to-tool co-impact, depending on the stiffness coefficient, was 200...300 μs. With a load of up to 90 kN in the time range of 0...4 ms, the normal stresses in the tool sections at different times were 200...250 MPa. The combination of discrete and continuous elements simplifies the calculation scheme. It allows to determine the distribution of force characteristics in the cross-sections of the tool, the force and time of impact, and the influence of the working environment on these parameters. The developed model can be used to design impactors and optimize their parameters
17 December 2024 in POWER ENGINEERING: economics, technique, ecology
This article examines the functioning of an adaptive impulse system with an electro-hydraulic drive for influencing the near-bore zone of an oil well from the surface without stopping hydrocarbon production. Particular attention was paid to the definition of the structure and functions of the electrohydraulic drive of the pulse system, and the rational zone of operation of the implosion pulse generator was determined with the establishment of restrictions on its operation. The article presents a mathematical model of the implosive impulse process and a functional-logistic model of adaptation of the impulse system to the conditions of the working environment. The variant of the system layout with the installation of an implosion pulse generator on the pump unit for action from the surface on the near-breakout zone of the oil well was considered. The rational length of the implosion chamber was determined and the area of operation of the adaptive pulse system with the generation of rational values of water hammer pressure was established. The paper presents the results of the industrial approval of the adaptive impulse system with electrohydraulic control of the previous modification under the industrial conditions of Ukraine. The characteristics of the devices that were used in the process of industrial approval are given.
26 February 2025 in Eastern-European Journal of Enterprise Technologies
The object of this study is the oscillation process of an impact device with a two-element striker, which makes it possible to increase the efficiency of rock destruction and reduce the recoil on the device body. The task addressed was the construction of a mathematical model that describes the dynamic interaction between the striker elements and the tool while taking into account the resistance of the working medium and impulse loads on the device elements. In the given model, the tool is represented by a rod of variable cross-section, and the striker is represented by two discrete elements with reduced masses. The impact interaction is modeled by the presence of rigid and dissipative links and is described by a system of differential equations with initial and boundary conditions. To solve the initial boundary value problem, a numerical method has been used; the parameters of the method are determined by solving the model problem, which is constructed for a discrete model with three discrete masses. An increase in the co-impact time relative to a device with a solid striker by 1.5...2 times to values of 350...500 μs was established. With a load force of 50 to 500 kN in the time range of 0...1 ms and element speeds of 1...8 m/s, the normal stresses in the tool cross-sections were 200...380 MPa. The combination of discrete and continuous elements in the model made it possible to refine the numerical method, taking into account the essential properties inherent in the impulse interaction of the striker elements with the tool and the transfer of impact energy to the processing environment. The model built can be used in the design of impactors with optimal parameters for assessing the shape and duration of the shock pulse, in mining, construction, and oil production