Yujie Li

Yujie Li

Auto-generated profile, based on publicly available information

Yujie Li

Naval University of Engineering,Wuhan,China

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 March 2022 in Applied Thermal Engineering
Verified
Journal Article
Closed access
ZMZewei Meng
Zewei Meng
YLYongbao Liu
Yongbao Liu
YLYujie Li
Yujie Li
XHX. He
X. He

1 April 2021 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
ZMZewei Meng
Zewei Meng
YLYongbao Liu
Yongbao Liu
YLYujie Li
Yujie Li
YZYunsong Zhang
Yunsong Zhang
Residual stress is an important parameter to evaluate and predict the interfacial peeling and failure of a thermal barrier coating (TBC) system in the thermal cycle. Considering a non-uniform temperature field, an analytical model for predicting residual stress of the TBC-film cooling system was established. Based on the double-layer TBC-film cooling system, the analytical solutions were validated by comparing with the previous results. Then, the four-layer system, including the superalloy substrate (SUB), the metallic bond coat (BC), the thermally grown oxide (TGO), and the ceramic top coat (TC), was analyzed. The distribution of residual stress was discontinuous at the interface among the layers. The maximum peeling moment occurred at the BC/SUB interface, and the maximum shear stress occurred at the TGO/BC interface. Therefore, the probabilities, of which opening edge cracks (mode I) appeared at the BC/SUB interface and shearing edge cracks (mode II) appeared at the TGO/BC interface, were higher than that at other interfaces. The deflection and bending direction of the system were affected by the temperature difference and coefficient of thermal expansions. The large thickness of the coating could effectively improve the thermal insulation capacity of the system, but the peeling moment and shear stress also increased. Therefore, preventing the thermal growth of the TGO layer and reducing the thickness of the TC layer can improve the stability of the system and extend service lifetime of the system while ensuring that the cooling requirements for hot section components are met.

16 July 2018 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Verified
Journal Article
Closed access
ZMZewei Meng
Zewei Meng
XFXiaoqiang Fan
Xiaoqiang Fan
BXBing Xiong
Bing Xiong
YTYuan Tao
Yuan Tao
Complex flow field structure, which is induced by the leading edge of V-shaped cowl-lip in hypersonic inward turning inlet, causes severe thermal load. The V-shaped cowl-lip is simplified as the V-shaped leading edge. Both wind tunnel tests and numerical simulations are applied to study the flow field structures. And numerical simulation is used to investigate the heat flux. The result shows that the V-shaped leading edge, compared with blunt body and slender body, presents complex shock wave interaction and suffers from critical aerodynamic heating. The shape parameter of the V-shaped leading edge, angle θ of the leading edge, is not a sensitive parameter of the heat flux. It does not effectively reduce the maximum of the heat flux. Another shape parameter, ratio (R/r) of rounded radius and blunted radius, has obvious effect on the peak value of the heat flux. The heat flux does not decrease necessarily with increasing R/r when R/r<2. It reduces significantly with increasing R/r when 2<R/r6.

27 May 2022
Verified
Conference Paper
Closed access
XDXiangyu Dong
Xiangyu Dong
YYYouhong Yu
Youhong Yu
YLYujie Li
Yujie Li
In view of the fact that a marine gas turbine is prone to compressor scaling, abnormal axial force, temperature field distortion and even abnormal blade wear when it runs in the marine environment for a long time, this paper aims to use the big data analysis method to study the degradation process of the gas turbine in use. Based on the traditional experience analysis method, this paper puts forward a method of establishing degradation evaluation index based on correlation analysis, establishes a degradation evaluation model based on support vector description, introduces the concept of degradation degree, and analyzes the degradation of a certain gas turbine through experiments, and achieves good results.