1 April 2015 in Engineering Geology
1 March 2023 in Géotechnique
Binary granular soil mixtures, as common heterogeneous soils, are ubiquitous in nature and man-made deposits. Fines content and particle size ratio are two important gradation parameters for a binary mixture, which have potential influences on mechanical behaviours. However, experimental studies on drained shear behaviour considering the whole range of fines content and different particle size ratios are scarce in the literature. For this purpose, a series of drained triaxial compression tests was performed on dense binary silica sand mixtures with four different particle size ratios to investigate systematically the effects of fines content and particle size ratio on the drained shear behaviours. Based on these tests, the strength-dilation behaviour and critical state behaviour were examined. It was observed that both fines content and particle size ratio have significant influence on the stress–strain response, the critical state void ratio, the critical state friction angle, the maximum dilation angle, the peak friction angle and the stress–dilatancy relation. The underlying mechanism for the effects of fines content and particle size ratio was discussed from the perspective of the kinematic movements at particle level.
18 April 2011 in Marine Georesources & Geotechnology
This article investigates the penetrability of microfine cement suspensions prepared with Rheocem 900 with and without superplasticizer additive into various graded fine-to-medium sands into which chemical grout permeation is only possible. Initially, the basic rheological properties such as viscosity, setting time, and stability of microfine cement suspensions are studied. In addition, penetration performance of the suspensions into various graded fine to medium sand specimens under different grouting pressures is examined. Finally, the strength and permeability characteristics of various graded fine-to-medium sand specimens permeated with microfine cement suspensions are studied. It is found that a superplasticizer additive greatly increases the grouting performance of microfine cement and reduces the grouting pressure. Moreover, it is seen that the unconfined compressive strengths of sand specimens permeated with a cement grout without additive are slightly less than those of sand specimens permeated with cement grout and superplasticizer additive. Furthermore, permeability tests on specimens permeated with cement grouts with or without a superplasticizer reveals that all specimens are impermeable (k < 1 × 10−7 m/s).
29 January 2021 in Acta Geotechnica
1 October 2009 in Geosynthetics International
This paper describes the findings of a series of laboratory unconfined compression tests and split tensile tests performed on specimens of varying fiber–sand–clay proportions. Sand was mixed with clay at six different proportions, namely 0.0, 1.0, 2.5, 5.0, 7.5, and 10.0% by dry weight of clay. Fiber was included in the sand–clay mixture at four different percentages, namely 0.0, 0.25, 0.5, and 1.0% by dry weight of clay. Compaction characteristics of the sand–clay mixtures were evaluated at standard compaction energy. According to fiber content, four groups of samples were prepared at maximum dry unit weight and optimum water content. For each of the four sample groups, unconfined compressive stress-axial strain and split tensile stress-diametrical strain behavior of the fiber–sand–clay mixtures were investigated. The test results showed that unconfined compressive strength (UCS) reached its maximum value at a fiber/clay ratio of 1.0% and sand/clay ratio of 7.5%. There was a reasonably strong linear correlation (R2≈ 1.0) between UCS and average initial tangent modulus values. The ratio of UCS to split tensile strength (STS) for all fiber–sand–clay mixtures varied between 3.2- and 5.8-fold.
1 December 2009 in Journal of Geotechnical and Geoenvironmental Engineering
The liquefaction susceptibility of various graded fine to medium saturated sands are evaluated by stress controlled cyclic triaxial laboratory tests. Cyclic triaxial tests are performed on reconstituted specimens having global relative density of 60%. In all cyclic triaxial tests, loading pattern is selected as a sinusoidal wave form with 1.0 Hz frequency and effective consolidation pressure is chosen as 100 kPa. Liquefaction resistance is defined as the required cyclic stress ratio causing initial liquefaction in 10 cycles during the cyclic triaxial test. The results are used to draw conclusions on the effect of the extreme void ratios and void ratio range on the liquefaction resistance of various graded sands.