14 September 2010 in Fire and Materials
1 November 1999 in Journal of Testing and Evaluation
Ultrasonic wave velocities (longitudinal and transverse waves) and the attenuation coefficient were used to investigate damage of aluminum 7075-T651 before and after progressive stages of fatigue. Repeated observations under controlled conditions allied to digital signal acquisition, autocorrelation, and regression were used to estimate small velocity and attenuation changes. Although comparatively small uncertainties were observed, the feasibility of utilizing the velocity of ultrasonic waves as a fatigue monitor was not substantiated under actual research conditions. However, careful measurements of the ultrasonic attenuation parameter demonstrated its potential to provide an early assessment of damage during fatigue. Part I of this work discussed the theoretical approach and described the fatigue testing procedures adopted in this investigation. This is a presentation and discussion of the experimental results.
10 October 2017 in Materials Science Forum
In the current restoration practice, the mortars based on aerial or hydraulic lime with siliceous aggregate are used on repair / reconstruction of historical plasters. The resulting properties of lime mortars do not depend only on the type of aggregate, but also on its contamination, origin and a degree of hardening. For this reason, it is needed to know a detailed characteristic of the aggregate and the results obtained for the particular aggregate cannot be generally applied for the similar type of aggregate. This work presents the applicability of Czech local crushed limestone aggregate and limestone fines as a filler to natural hydraulic lime-based mortars. The role of aggregate and limestone fines on the properties of mortars is examined by comparing the mechanical strengths, porosity and frost resistance of the mortars with pure quartz sand and limestone aggregate and its quantity in the mortar. It was found that the limestone aggregate has produced lower strengths, higher total porosity of natural hydraulic lime-based mortars. It has resulted in low frost resistance of the mortars.
20 June 2018 in Solid State Phenomena
This paper studies the possibility of usage of chitosan derivatives (hydroxypropyl chitosan (HPCH) and carboxymethyl chitosan (CMCH)) as admixtures for aerial lime-based mortars. The physical-mechanical properties were studied on the specimens prepared with constant water/binder ratio and binder/aggregate ratio 1:3 by weight using siliceous sand with the grain size up to 4 mm and doses of admixture ranging between 0.5 and 10‰. The properties were studied on the specimens up to 365 days. The addition of admixtures improves workability of mortar, but in the early stages also decreases strengths of mortars, especially the compressive strength. The addition of HPCH significantly reduces the bulk densities of specimens, while CMCH decreases them just slightly. With the increasing amount of time, the difference in strengths between reference and tested mortars decreases, reaching the similar values after 90 days of curing time. The further ageing causes additional growth of strengths with a significantly higher increase in the case of CMCH.
15 January 2018 in Key Engineering Materials
This paper studies the possibility of usage of the guar gum and its derivatives (carboxymethylhydroxypropyl guar (CMHPG) and hydroxypropyl guar (HPG)) as admixtures for aerial lime-based mortars. The influence on the properties of mortars was studied on the aerial lime –based mortars prepared with quartz fine grained sand and doses of admixtures ranging between 0,5 and 10‰. The hardened bulk densities, flexural and compressive strength, porosity, water absorption coefficient due to capillarity action and carbonation rate were studied. The addition of the hydroxypropyl guar lowered the bulk density (due to an air intake), improved workability, slightly increased the strength, slowed carbonation rate, and nobbled the water transport in the mortar. The addition of carboxymethylhydroxypropyl guar does not impact the bulk density, the strengths were increased similarly to HPG: it does not impact carbonation rate significantly, so the long term strengths were comparative with the HPG. The water transport was slightly better in lower doses and slightly worse in larger doses in comparison with the reference mortar. The pure guaran was found not to be beneficial for the lime mortars for its only advantage is in the water transport, where in any dose the transport was better than any other mortar, but the benefit of this is questionable.
16 August 2019 in Solid State Phenomena
In this study, the utilization of lava sand as an aggregate in lime mortars, cement-lime mortars and natural hydraulic lime mortars has been investigated. The aim of this study is to compare some physico-mechanical and microstructural properties of lava sand mortars with reference mortars with pure quartz sand. Compressive and flexural strengths were tested at mortar age of 28, 56 and 90 days. The results revealed improved flexural strengths of mortars with lava sand despite the fact that the mortars showed higher open porosity and water absorption than those with quartz aggregate. This fact predetermines the use of lava sand in non-hydrophobic remedial mortars with a high ability to salt accumulation from masonry. The applied lava sand is convenient to lime-based mortars as an aggregate, especially in regions where the lava resources are abundant.