Jorge Luis Alamilla

Jorge Luis Alamilla

Auto-generated profile, based on publicly available information

Jorge Luis Alamilla

IMP Mexican Institute of Petroleum

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 August 2010 in Journal of Pressure Vessel Technology
Verified
Journal Article
Closed access
PDF file
MBM. Bony
M. Bony
JAJ. L. Alamilla
J. L. Alamilla
RVR. Vai
R. Vai
EFE. Flores
E. Flores
Simple and accurate approaches to predict failure pressures in corroded pipelines are outlined in this work. It is shown that failure pressures for corroded pipelines can be predicted from the solution for undamaged pipelines using an equivalent wall thickness. Three different yield criteria (Tresca, ASSY (average shear stress yield), and von Mises) are reviewed in the light of reported experimental burst pressures. At first, failure pressures for cylindrical vessels with an infinitely long groove are studied by means of numerical simulations. The effect of groove size (depth and width) over the pipeline performance is quantified through a model. Finally, the scheme is extended to estimate the failure pressure of thin walled vessels with irregular finite defects.

15 September 2020 in Bulletin of the Seismological Society of America
Verified
Journal Article
Closed access
PDF file
JAJorge L. Alamilla
Jorge L. Alamilla
JRJosé A. Rodriguez
José A. Rodriguez
RVRossana Vai
Rossana Vai
Cornell’s, Esteva’s, and classical formulations for seismic hazard analysis are theoretically described and mathematically unified by a suitable treatment of the random ground-motion variable. Differences and connections among the schemes are discussed, allowing for a better understanding of the underpinning principles of probabilistic seismic hazard analysis. The classical formulation is equivalent to that by Esteva, and they correspond to a general scheme. Although they are mathematically equivalent, the two formulations each has its own particular approach to express the hazard rate, so results may differ. Cornell’s original scheme is a particular case of classical and Esteva’s formulation. It is also shown that intensity exceedance rates for any index of structural performance or at a particular site can be recursively transformed into exceedance rates of other intensity indexes. Formulations are invariant under such a transformation.

30 August 2006 in Earthquake Engineering & Structural Dynamics
Verified
Journal Article
Closed access
PDF file
JAJorge L. Alamilla
Jorge L. Alamilla
LELuis Esteva
Luis Esteva

11 June 2018 in Anti-Corrosion Methods and Materials
Verified
Journal Article
Closed access
LALuis Quej Ake
Luis Quej Ake
ACAntonio Contreras
Antonio Contreras
HLHongbo Liu
Hongbo Liu
JAJ.L. Alamilla
J.L. Alamilla
ESE. Sosa
E. Sosa
Purpose: The purpose of this paper is to study the susceptibility to corrosion processes of X60, X65 and X70 steels immersed in sand-clay soil with pH 3.0, using electrochemical techniques, scanning electron microscopy (SEM), energy dispersive spectroscopy and X-ray diffraction (XRD). Design/methodology/approach: Natural acidic soil sample was collected as close as possible to buried pipes (1.2 m in depth) in a Right of Way from south of Mexico. Both steels and soil were characterized through SEM and XRD. Then, open circuit potential was recorded for all steels exposed to soil at different exposure times. Thus, the electrochemical impedance spectroscopy (EIS) was traced, and anodic polarization curves were obtained. Findings: The steel corrosion processes started when the active sites were exposed to natural acidic soil. However, corrosion rates decreased for three steels as immersion time increased, obtaining the highest corrosion rate for X60 steel (0.46 mm/year for 5 h). This behavior could be attributed to corrosion products obtained at different exposure times. While, 5 h after removing corrosion products, X65 steel was more susceptible to corrosion (1.29 mm/year), which was corroborated with EIS analysis. Thus, corrosion products for the three steels exposed to natural acidic soil depended on different microstructures, percentage of pearlite and ferrite phases, in which different corrosion processes could occur. Therefore, the active sites for carbon steel surfaces could be passivated with corrosion products. Practical implications: The paper identifies the any implication for the research. Originality/value: Some anodic peaks could be caused by metallic dissolution and was recorded using high positive polarization (high field of perturbation). In addition, the inductive effects and diffusion process were interpreted at low frequency ranges using EIS. According to X-ray diffraction (XRD), acidic soil had Muscovite containing aluminum and iron phases that were able to generate hydrogen proton at the presence of water; it might be promoted at the beginning of deterioration on low carbon steels. Steel surface cleaning after removing corrosion products was considered to study the possible diffusion phenomena on damaged steel surfaces using EIS.

27 July 2014 in Journal of Seismology
Verified
Journal Article
Closed access
PDF file
JAJorge L. Alamilla
Jorge L. Alamilla
RVRossana Vai
Rossana Vai
LELuis Esteva
Luis Esteva

6 August 2014 in Journal of Seismology
Verified
Journal Article
Closed access
PDF file
JAJorge L. Alamilla
Jorge L. Alamilla
RVRossana Vai
Rossana Vai
LELuis Esteva
Luis Esteva