Mochammad Syamsul Ma’arif

Mochammad Syamsul Ma’arif

Auto-generated profile, based on publicly available information

Mochammad Syamsul Ma’arif

Brawijaya Univ, Mech Engn Dept, Mayjend Haryono St 167, Malang 65145, Indonesia

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 March 2023 in MM Science Journal
Verified
Journal Article
Closed access
SUSugiarto
Sugiarto
MMMoch. Syamsul Ma’arif
Moch. Syamsul Ma’arif
HPHelmy Purwanto
Helmy Purwanto
WMWayan Jorsa Ery Mahendra
Wayan Jorsa Ery Mahendra
HOHizkia Oswari
Hizkia Oswari
The MM Science Journal, published since 2008, is a world respected scientific journal. The journal, published in English, is double peer reviewed and competitive in distributing knowledge among domestic and international academics and professionals. Full texts are available on-line on the journal...

11 December 2024 in MM Science Journal
Verified
Journal Article
Closed access
SUSugiarto
Sugiarto
MMMoch. Syamsul Ma’aRif
Moch. Syamsul Ma’aRif
AWAri Wahjudi
Ari Wahjudi
MYMuhammad Ichsan Yozianto
Muhammad Ichsan Yozianto
Friction stir welding (FSW) can be a solution in solving the problem of joining thermoplastic polymers which are difficult to do with fusion welding. Selection of the proper FSW connection parameters can produce optimal connection quality in HDPE material joints. In friction stir welding, the heat of welding is used to raise the temperature of the material from its initial state to the solid state temperature. If the material temperature (T0) is increased above room temperature (TRoom), while the FSW welding parameter is constant, then at a certain increase in T0 it will produce excess welding heat which results in excessive softening or even melting of the material being welded. Therefore, the material temperature setting (T0) becomes an important parameter FSW The process of connecting the HDPE plates with friction stir welding was carried out by varying the material temperature (T0 ) of TRoom, 50 0C, 75 0C and 100 0C. While the spindle rotation varies 2000 rpm and 2500 rpm. Other parameters controlled include the type of square butt joint, 5 mm HDPE plate thickness, 20 mm/min feed rate, 0.1 mm plunge depth, 20 mm tool shoulder diameter, 4.5 mm pin length and 6 mm pin diameter. The result is that the higher the spindle rotation and the material temperature during the welding process causes the FSW peak welding temperature to increase. The highest peak weld temperature was obtained at variations in material temperature (T0) 100 °C with a spindle rotation of 2500 rpm, which is 123.2 °C or 94% of the melting temperature of HDPE. The hardness of the weld nugged area is still lower than the hardness of the base material. The highest average tensile strength of the research variations was achieved at a spindle rotation speed of 2500 rpm and a material temperature of 75 °C of 16.8 MPa, higher than the average tensile strength of the base material which is 15.1 MPa.

15 May 2020 in Jurnal Rekayasa Mesin
Verified
Journal Article
Open access
PDF file
RBRedi Bintarto
Redi Bintarto
TWTeguh Dwi Widodo
Teguh Dwi Widodo
RRRudianto Raharjo
Rudianto Raharjo
MMMoh. Syamsul Ma’arif
Moh. Syamsul Ma’arif
FDFrancisca Gayuh Utami Dewi
Francisca Gayuh Utami Dewi
GPGesha Denny Pratama
Gesha Denny Pratama
This study aims to determine the various effect of heat input due to varied electric current on microstructure of the weld joints and the bending strength of 2 dissimilar metals (aluminum alloy 5052 and galvanized steel) with Al-Si 4043 as filler. This experimental research was worked out by varying the strength of the current which can then be calculated into a heat input. The current inputs applied were 30.8 J / mm (70A), 35.2 J / mm (80A) and 39.6 J / mm (90A) while the protective gas flow rate used is 14 liters / minute. This study showed that the increase in heat input greatly affects the shape of the weld area microstructure, i.e. the microstructure and bending strength. Greater heat input due to higher current can melt larger area, so that the join process occured better. The highest bending strength at 9.05 Mpa was achieved for heat input at 39.6 J / mm or strong current of 90 A. The weakest bending strength at 8.88 Mpa was achieved for heat input at 35.2 J / mm or a strong current of 70 A.

29 May 2023 in Community Empowerment
Verified
Journal Article
Open access
PDF file
MMMoch. Syamsul Ma'Arif
Moch. Syamsul Ma'Arif
SSSugiarto Sugiarto
Sugiarto Sugiarto
ESErwin Sulistyo
Erwin Sulistyo
At Taman Embong Anyar 1 Housing Complex in Dau District, Malang, there is a high crime risk due to residents' activity patterns and open access to residential areas. One of the community's biggest issues is a lack of understanding of using security technology. As an alternative to monitoring the situation in residential areas, CCTV installation and operation assistance are needed to increase environmental security. Beginning with a survey of the areas where CCTV must be installed, the CCTV system must then be selected, installed, and its operation explained to all users. The residents can use and maintain the CCTV system as a result of the entire series of activities. The environment is made more secure and the workload of security officers is minimized with the installation of CCTV.

1 May 2024 in BIO Web of Conferences
Verified
Journal Article
Open access
PDF file
MMMoch. Syamsul Ma’arif
Moch. Syamsul Ma’arif
IWI Nyoman Gede Wardana
I Nyoman Gede Wardana
PPPurnami Purnami
Purnami Purnami
DDDjarot Bangun Darmadi
Djarot Bangun Darmadi
ONOyong Novareza
Oyong Novareza
ZAZainal Abidin
Zainal Abidin
Lubrication in machining process plays a very important role in machining because it increases the productivity and quality of the machining process. Today, most Metalworking Fluids (MWF) are petroleum based ones. Due to its advantages, the consumption of MWF is increasing therefore creating many negative effects on the environment. These effects are related to surface and groundwater, and soil contamination. To address this challenge, various MWF alternatives are being explored by scientists. Vegetable oil is a very attractive alternative to petroleum-based lubricants, because vegetable oils are environmentally friendly, renewable, non-toxic, and easily biodegradable. In complement to the experimental method, simulations using chemical application programs such as Hyperchem 8.0 can also be carried out to provide an estimate of how the interaction between components of lubricating oil, lubricating oil and additives, as well as lubricating oil and additives to their attraction properties to certain surfaces (such as metals). In this study, the effect of the addition of eugenol as a bio-additive on the interaction between molecules of jatropha oil lubricant on the surface of the material will be analysed. The results obtained are simulations using Hyperchem 8.0 can be used to predict the physical properties of the lubricating oil.

30 May 2019 in Journal of Energy, Mechanical, Material and Manufacturing Engineering
Verified
Journal Article
Open access
PDF file
MMMoch. Syamsul Ma'ARif
Moch. Syamsul Ma'ARif
CCChristopher David Cook
Christopher David Cook
Lighter construction in the structure of transportation make industries rely on aluminium as construction materials and new technology of joining such as friction stir welding become increasingly applied. Since welding force in the process is considered high so that many researches are focussed on this area. In this research, a new method of welding by using non-rotating shoulder tool and combined with pre heating was investigated. The result give confirmation that the methods was proven to be adequate to produce sound welding when the parameters chosen was rightly. Eventhough the method was able to lower the force but significant results only observed for Fx while another force, i.e. Fz, did not have similar significant results. Non-rotating shoulder with additional heat input has limited capability in lowering forces in Fz because of its design, while has very good capability to lower Fx. Also, it was obvious that the heat source using propane torch was not adequate to give uniform additional heat input in all welding phase and still need another moee porent heat source in order to improve the performance.