Lech Gładysiewicz

Lech Gładysiewicz

Auto-generated profile, based on publicly available information

Lech Gładysiewicz

Department of Mining, Faculty of Geoengineering, Mining and Geology, Wrocław University of Science and Technology (WUST), Na Grobli 15, 50-421 Wrocław, Poland

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 March 2021 in Energies
Verified
Journal Article
Open access
PDF file
PBPiotr Bortnowski
Piotr Bortnowski
LGLech Gładysiewicz
Lech Gładysiewicz
Robert KrolRobert Krol
Robert Krol
MOMaksymilian Ozdoba
Maksymilian Ozdoba
Milling is among the most energy-consuming technological stages of copper ore processing. It is performed in mills, which are machines of high rotational masses. The start of a mill filled to capacity requires appropriate solutions that mitigate the overloading. One method for increasing the energy efficiency of ball mills is to optimize their drive systems. This article looks at two variants of drive systems with efficiencies higher than the already existing solutions. The first variant is a low-speed synchronous motor with permanent magnets without a gearbox, and the second variant is an asynchronous high-efficiency motor with a gearbox and a fluid coupling. The energy performance analysis of the three solutions was based on the average energy consumption indicator per mass unit of the milled material and on the energy consumption per hour. The investigations required models of the drive systems and analyses with the use of the Monte Carlo methods. The highest energy efficiency is observed in the case of the solution based on the permanent magnet motor. However, the drive system with the high-speed motor offers a gentle start-up possibility owing to the fluid coupling.

9 July 2021 in Energies
Verified
Journal Article
Open access
PDF file
PBPiotr Bortnowski
Piotr Bortnowski
LGLech Gładysiewicz
Lech Gładysiewicz
Robert KrolRobert Krol
Robert Krol
MOMaksymilian Ozdoba
Maksymilian Ozdoba
The transverse vibration frequency of conveyor belts is an important parameter describing the dynamic characteristics of a belt conveyor. This parameter is most often identified from theoretical relationships, which are derived on the basis of an assumption that the belt is a stationary elastic string. Belt vibrations have a number of analogies to other tension member systems, such as, for example, power transmission belts. Some research findings suggest that in the case of a limited length of the belt section, a more accurate description of its vibration can be obtained with a beam model rather than with a string model. Experimental research has so far mostly revolved around measurements of stationary belts. This article presents the results of vibration measurements performed for a moving belt and obtained for various operating parameters of the conveyor, as well as for several configurations of the distance between idler supports. The analysis was conducted on a moving steel-cord belt. Belts of this type are commonly used in the majority of mines and industrial plants. The measurement results were compared with the model of a string and with the model of a beam in tension. Both of the theoretical models allowed for the belt speed, whose influence was demonstrated in both theoretical calculations and experimental tests to be negligible. On the other hand, the tensile force in the belt was observed to have a significant impact on the vibration frequency. Depending on the idler spacing, the measurement results are approximate to those of the beam model or of the string model. For spacing smaller than 1.6 m, the belt shows properties approximate to an elastic beam, while for spacing greater than 1.6 m, the belt behaviour can be better represented through a string model. A beam model is, therefore, more applicable in analyses of vibrations in the upper strand of the belt, while a string model is more useful in analyses of vibrations in the lower strand.

21 August 2022 in Energies
Verified
Journal Article
Open access
PDF file
PBPiotr Bortnowski
Piotr Bortnowski
AGAdam Gładysiewicz
Adam Gładysiewicz
LGLech Gładysiewicz
Lech Gładysiewicz
Robert KrolRobert Krol
Robert Krol
MOMaksymilian Ozdoba
Maksymilian Ozdoba
Intermediate linear booster drive can solve many problems of transport by long route conveyors. At the same time, operating costs are significantly reduced. There are solutions using intermediate belt drives, usually involving friction coupling in the carry belt. From a theoretical point of view, it is possible to transmit the friction force on an additional section in the return belt. The article presents a theoretical and experimental analysis of this solution and a comparison with a drive operating in a conventional solution. The transferred forces, the variability of the belt tension as well as the efficiency and stability of the drive for both solutions were compared. The use of additional coupling in the return belt makes it possible to increase the transmitted friction force and achieve a better rate of electricity consumption. The solution can be useful in currently existing intermediate drives, where it is possible to support the return side and transmit power.

14 October 2020 in Sensors
Verified
Journal Article
Open access
PDF file
PBPiotr Bortnowski
Piotr Bortnowski
LGLech Gladysiewicz
Lech Gladysiewicz
Robert KrolRobert Krol
Robert Krol
MOMaksymilian Ozdoba
Maksymilian Ozdoba
In the locations where driving forces are transmitted, the changing tensile forces cause rapid elastic deformations of the belt. The deformation changes the belt speed. Measurement of the belt speed on the friction contact sections is essential to identify elastic slippage. However, the scale of the phenomenon is small, so it is necessary to use precise measuring equipment. The article presents measurements of the linear belt speed with the use of various sensors and measuring devices. A measurement error was determined for each of the presented measurement methods. The method with the highest accuracy was used to identify the elastic slippage on the drive pulley.

31 January 2018 in E3S Web of Conferences
Verified
Conference Paper
Open access
DWDariusz Woźniak
Dariusz Woźniak
LGLech Gładysiewicz
Lech Gładysiewicz
MKMartyna Konieczna-Fuławka
Martyna Konieczna-Fuławka
Belt conveyors are main part of transporting systems in mines and in many other branches of industry. During conveyor belt works different types of resistances are generated. Indentation rolling resistance is the most significant component of the resistances from the perspective of energy losses and it cause the biggest costs as well. According to latest state of analyses and measurements it is well known that theoretical rolling resistance were underestimated in comparison with the measured in-situ one. In this paper new method for determination indentation rolling resistance is presented. The authors compared theoretically and experimentally established damping factors. The relation between these two values enabled to obtain more precise equation for damping function. This function is one of the most important component in calculation of the rolling resistance. In new theoretical model value of rolling resistance is nearly twice higher than this used so far.