Fahad Ali

Fahad Ali

Auto-generated profile, based on publicly available information

Fahad Ali

Department of Metallurgy and Materials Engineering, Pakistan Institute of Engineering and Applied Sciences, Islamabad (PIEAS), Islamabad, Pakistan

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2017 in Materials Science and Technology
Verified
Journal Article
Closed access
MKMahmood Khan
Mahmood Khan
MZMuhammad Zulfaqar
Muhammad Zulfaqar
FAFahad Ali
Fahad Ali
TSTayyab Subhani
Tayyab Subhani
Hybrid composites of boron carbide (B4C) and Al62.5Cu25Fe12.5 quasicrystals (QCs) were prepared by ball milling and pressureless sintering in aluminium matrix to investigate their individual and hybrid effects on microstructural and mechanical properties. Hybrid composite contained B4C and QCs in 3 wt-% each, making a total of 6 wt-%. For reference, specimens of pure aluminium and two composites containing 6 wt-%B4C and 6 wt-% QCs were prepared. Microstructural characterisation was performed using optical, scanning electron microscopy and X-ray diffraction, while evaluation of mechanical properties was carried out by hardness and compression tests. Uniform dispersion of reinforcements in composites was observed along with significant increase in the mechanical properties. The composite containing 6 wt-% QCs demonstrated the highest hardness, while the hybrid composite showed better compressive properties.

5 August 2018 in Powder Metallurgy
Verified
Journal Article
Closed access
ZAZ. Asghar
Z. Asghar
MLMuhammad Adnan Latif
Muhammad Adnan Latif
RDRafi- Ud- Din
Rafi- Ud- Din
ZNZeeshan Nazar
Zeeshan Nazar
FAFahad Ali
Fahad Ali
TSTayyab Subhani
Tayyab Subhani
In this work, the effect of mixing parameters on the distribution of B4C in 6061-Al alloy and its correlation with mechanical behaviour was studied. 6061-Al alloy powder was mixed with 10 mass-% B4C powder in a ball mill and powder rotator mixer by varying mixing time from 1 to 5 h. Mixing was performed in both wet and dry conditions in a ball mill while only dry condition was used in the powder rotator mixer. The green compacts were sintered at 630°C. The quadrat method was used to quantify the distribution of B4C particles in the microstructures of sintered Al/B4C composite. The results showed that the distribution was improved with mixing time but the density, hardness and compression strength of Al/B4C composites were reduced with time during ball milling. On the other hand, the distribution of reinforcement, density, hardness and compressive strength of Al/B4C composites was improved with mixing time in the powder rotator mixer.

1 September 2015 in Materials & Design (1980-2015)
Verified
Journal Article
Closed access
JKJ. Kamran
J. Kamran
USUd Din Shamas
Ud Din Shamas
NTNaeem ul Haq Tariq
Naeem ul Haq Tariq
FAF. Ali
F. Ali
BHB.A. Hasan
B.A. Hasan

23 December 2020 in Journal of Energetic Materials
Verified
Journal Article
Closed access
RARashid Ali
Rashid Ali
FAFahad Ali
Fahad Ali
AZAqib Zahoor
Aqib Zahoor
RSRub Nawaz Shahid
Rub Nawaz Shahid
NTNaeem Ul Haq Tariq
Naeem Ul Haq Tariq
HAHasan Bin Awais
Hasan Bin Awais
Aluminum powders are well known for excellent release of energy during oxidation upon heating. However, this release of energy becomes limited due to formation of dense oxide (Al2O3) layer on powder surface. In this study, reactivity of aluminum particles was improved by replacing oxide layer with metallic shell of iron using electroless plating technique. Three different bath compositions were selected for deposition of iron on aluminum particles. The surface morphology of prepared Al/Fe core–shell composite powder was characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). Further, iron content in the composite powder was measured quantitatively using helium gas pycnometer while elemental analysis was performed by X-ray diffraction (XRD). Finally, thermo-physical behavior of the composite powder was investigated using simultaneous thermogravimetry–differential scanning calorimetry (TG–DSC). The results showed that the synthesized Al/Fe core–shell composite powder exhibits higher energy release in comparison to the uncoated aluminum powder upon heating in air (up to 1180 °C). The powder with the densest iron coating released the highest energy.

11 November 2013 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
NMN. K. Mukhopadhyay
N. K. Mukhopadhyay
FAF. Ali
F. Ali
SSSergio Scudino
Sergio Scudino
MKM. Samadi Khoshkhoo
M. Samadi Khoshkhoo
MSMihai Stoica
Mihai Stoica
JEJürgen Eckert
Jürgen Eckert
Inverse Hall-Petch (IHP) behavior in nano-quasicrystalline Al62.5Cu25Fe12.5 is reported. Powders with varying grain sizes were produced by mechanical milling of spray-formed quasicrystals. The hardness of the milled powders increased with decreasing grain size down to about 40 nm and decreased with further refinement, demonstrating the IHP behavior. This critical grain size was found to be larger compared to other metallic nanocrystalline alloys. This IHP behaviour has been attributed to the structural complexity in quasicrystals and to thermally activated shearing events of atoms at the grain boundaries.

20 May 2020 in Applied Physics A
Verified
Journal Article
Closed access
PDF file
AZAqib Zahoor
Aqib Zahoor
TATaha Aziz
Taha Aziz
SZSoumble Zulfiqar
Soumble Zulfiqar
ASAisha Sadiq
Aisha Sadiq
RARashid Ali
Rashid Ali
HAHasan Bin Awais
Hasan Bin Awais