Masoud Sakaki

Masoud Sakaki

Auto-generated profile, based on publicly available information

Masoud Sakaki

Institute of Technology for Nanostructures and CENIDE, University of Duisburg-Essen, Duisburg, Germany

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 April 2022 in IEEE Access
Verified
Journal Article
Open access
PKPetr Kadera
Petr Kadera
JSJesús Sánchez-Pastor
Jesús Sánchez-Pastor
HEHossein Eskandari
Hossein Eskandari
TTTomas Tyc
Tomas Tyc
MSMasoud Sakaki
Masoud Sakaki
JLJaroslav Lacik
Jaroslav Lacik
This paper presents a quasi-conformal transformation optics (QCTO) based three-dimensional (3D) retroreflective flattened Luneburg lens for wide-angle millimeter-wave radio-frequency indoor localization. The maximum detection angle and radar cross-section (RCS) are investigated, including an impedance matching layer (IML) between the lens antenna and the free-space environment. The 3D QCTO Luneburg lenses are fabricated in alumina by lithography-based ceramic manufacturing, a 3D printing process. The manufactured structures have a diameter of 29.9 mm ( $4 \lambda _{0}$ ), showing a maximum realized gain of 16.51 dBi and beam steering angle of ±70° at 40 GHz. The proposed QCTO Luneburg lens with a metallic reflective layer achieves a maximum RCS of −20.05 dBsqm at 40 GHz with a wide-angle response over ±37°, while the structure with an IML between the lens and air improves these values to a maximum RCS of −15.78 dBsqm and operating angular response between ±50°.

1 May 2015 in International Journal of Refractory Metals and Hard Materials
Verified
Journal Article
Closed access
AHArman Hoseinpur
Arman Hoseinpur
MBMohammad Sh. Bafghi
Mohammad Sh. Bafghi
JKJalil Vahdati Khaki
Jalil Vahdati Khaki
MJMaisam Jalaly
Maisam Jalaly
MSMasoud Sakaki
Masoud Sakaki

1 November 2009 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MSM. Sakaki
M. Sakaki
MBM.Sh. Bafghi
M.Sh. Bafghi
JKJ. Vahdati Khaki
J. Vahdati Khaki
QZQ. Zhang
Q. Zhang
FSF. Saito
F. Saito

1 July 2009 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
MSM. Sakaki
M. Sakaki
MBM.Sh. Bafghi
M.Sh. Bafghi
JKJ. Vahdati Khaki
J. Vahdati Khaki
QZQ. Zhang
Q. Zhang
JKJ. Kano
J. Kano
FSF. Saito
F. Saito

1 January 2013 in International Journal of Refractory Metals and Hard Materials
Verified
Journal Article
Closed access
MSM. Sakaki
M. Sakaki
MBM.SH. Bafghi
M.SH. Bafghi
JKJ. Vahdati Khaki
J. Vahdati Khaki
QZQ. Zhang
Q. Zhang
FSF. Saito
F. Saito

13 December 2023 in Journal of the American Ceramic Society
Verified
Journal Article
Open access
KJKai‐Daniel Jenkel
Kai‐Daniel Jenkel
JSJesús Sánchez‐Pastor
Jesús Sánchez‐Pastor
MBMohammad Mahdi Baloochian
Mohammad Mahdi Baloochian
RJRolf Jakoby
Rolf Jakoby
MSMasoud Sakaki
Masoud Sakaki
NBNiels Benson
Niels Benson
This contribution discusses the impact of sintering temperatures on dielectric properties of 3D‐printed alumina (Al 2 O 3 ) in the W‐band, by evaluating high quality factor (− Q ) resonators integrated in a 2D photonic crystal structure. By varying the sintering temperature of the lithography‐based ceramic manufactured (LCM) samples, the microstructure of the material can be defined, which has a direct impact on the dielectric permittivity and material losses. Using a highly accurate photonic crystal structure, with a dimensional variation below 2% from print to print, an accurate extraction and evaluation of the dielectric material properties could be achieved. The relative permittivity of the alumina was tuned from 4.4 at 1250°C to 9.2 at 1650°C, whereas the observed change in dielectric losses was moderate. The maximum in observed dielectric loss for samples sintered at the lowest evaluated temperature, only yields an average value of 30 × 10 −4 . This demonstrates the versatility of the LCM technology for mm‐ and sub‐mm‐wave applications and its possibilities for material tuneability.