Sergey Yershov

Sergey Yershov

Auto-generated profile, based on publicly available information

Sergey Yershov

Institute for Mechanical Engineering Problems of National Academy of Sciences of Ukraine, Kharkiv, Ukraine

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2005 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
PLPiotr Lampart
Piotr Lampart
ARAndrey Rusanov
Andrey Rusanov
SYSergey Yershov
Sergey Yershov
SMStanislaw Marcinkowski
Stanislaw Marcinkowski
AGAndrzej Gardzilewicz
Andrzej Gardzilewicz
A state equation of thermally perfect and calorically imperfect gas is implemented in a 3D RANS solver for turbomachinery flow applications. The specific heats are assumed as linear functions of temperature. The model is validated on a five-stage low-pressure steam turbine. The computational results exhibit the process of expansion in the turbine. The computed and measured distributions of flow parameters in axial gaps downstream of subsequent turbine stages are found to agree reasonably well. It is also shown that the obtained numerical solution gives considerable improvement over the solution based on the thermally and calorically perfect gas model.

1 January 2002 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
Verified
Journal Article
Closed access
SYS Yershov
S Yershov
ARA Rusanov
A Rusanov
ASA Shapochka
A Shapochka
PLP Lampart
P Lampart
JŚJ Świrydczuk
J Świrydczuk
AGA Gardzilewicz
A Gardzilewicz
A combination of the Nelder-Mead deformed polyhedron method with a three-dimensional RANS solver is used in the paper for the constrained optimization of the shape of two selected turbine stages. The objective function is the total stage loss, with the exit kinetic energy also considered a loss. There are constraints imposed on the mass flowrate, exit angle, average reaction and reaction at tip and root. The exit angle and reactions are not allowed to assume values beyond prescribed ranges, whereas a penalty function is imposed on the mass flowrate if it falls outside the required interval. Among the optimized parameters are stator and rotor stagger and twist angles and stator sweep and lean, both straight and compound. The computations of the flowfield are compressible, viscous and three-dimensional. Turbulence effects are taken into account using the modified Baldwin-Lomax model. The process of optimization gives new designs with improved calculated efficiency. Part of the improvementis due to optimization of the stagger angles and blade numbers, as in classical one-dimensional optimization, and part of it is due to the fact that the blades assume new three-dimensional stacking lines.

1 March 2005 in Engineering Optimization
Verified
Journal Article
Closed access
PLPiotr Lampart
Piotr Lampart
SYSergey Yershov
Sergey Yershov
ARAndrey Rusanov
Andrey Rusanov
3D blading of a high-pressure and low-pressure steam turbine stage is optimized using Nelder–Mead method of deformed polyhedron. Values of the minimized objective function, i.e. stage losses with the exit energy are found from 3D viscous compressible flow computations, including turbulence effects. Among the optimized parameters are stator and rotor blade numbers and stagger angles, rotor blade twist angle, stator blade sweep and lean, both straight and compound. The blade sections (profiles) are assumed not to change during the optimization. There are constraints imposed on the design parameters, including the mass flow rate and stage reaction. Optimization gives designs with new 3D blade stacking lines, and with increased efficiencies, compared with the original design.

1 January 2004
Verified
Conference Paper
Closed access
PDF file
PLPiotr Lampart
Piotr Lampart
SYSergey Yershov
Sergey Yershov
ARAndrey Rusanov
Andrey Rusanov
MSMariusz Szymaniak
Mariusz Szymaniak
Interaction of the main flow with tip leakage over shrouded rotor blades in a multi-stage turbine is studied numerically. The flow in blade-to-blade channels is computed with the aid of a 3D Navier-Stokes solver FlowER with the Menter SST turbulence model. In this paper, the labyrinth seals are not computed but the numerical scheme is modified to include the source/sink-type boundary conditions at places at the endwalls referring to design locations of injection of leakage flows into, or their extraction from, the blade-to-blade passage. Without considering complete labyrinth seal geometries, the tip leakage jet is represented by its flow rate and direction at re-entry to the blade-to-blade passage, as if referring to the performance of a range of different labyrinth seal arrangements. The effect of direction of tip leakage re-entry on the downstream flow and efficiency of the turbine stage (stage group) is studied. The calculation method is validated on a model air stator/rotor turbine.

30 March 2021 in Journal of Mechanical Engineering
Verified
Journal Article
Open access
F(Finland) Self-Employed Researcher (Oulu
Finland) Self-Employed Researcher (Oulu
SYSerhii V. Yershov
Serhii V. Yershov
VYViktor A. Yakovlev
Viktor A. Yakovlev
ANA. Pidhornyi Institute of Mechanical Engineering Problems of NASU
A. Pidhornyi Institute of Mechanical Engineering Problems of NASU
The question of the difference mesh refinement degree influence on the results of calculation of the three-dimensional viscous gas flows in the flow parts of turbomachines using the RANS flow models and second order numerical methods is considered. Calculations of flows for a number of turbine and compressor grids on successively refining grids have been performed. We used H-type grids with approximate orthogonalization of cells in the boundary layer. The calculations were carried out using a CFD solver F with the use of an implicit ENO scheme of the second order, a local time step, and a simplified multigrid algorithm. When calculating the flow on fine grids, the following were used: convergence acceleration tools implemented in the solver; truncation of the computational domain with subsequent distribution of the results based on the symmetry property; the computational domain splitting into parts and computations parallelizing. Comparison of the obtained results is carried out, both in terms of qualitative resolution of the complex structure of three-dimensional flows, and in terms of quantitative assessment of losses. Grid convergence was estimated in two ways. In the first, the characteristic two-dimensional distributions of parameters obtained on different grids were visually compared. The purpose of such comparisons was to evaluate the sufficient degree of solution of both the general structure of the flow in grids and its features, namely, shock waves, contact discontinuities, separation zones, wakes, etc. The second estimation method is based on the grid convergence index (GCI). The GCI calculated from the three-dimensional density field was considered in this paper. It is concluded that for scientific research requiring high accuracy of calculations and detailing of the structure of a three-dimensional flow, very fine difference meshes with the number of cells from 106 to 108 in one blade-to-blade channel are needed, while for engineering calculations, under certain conditions, it is sufficient to use meshes with the number of cells less than 1 million in one blade-to-blade channel.

27 December 2002 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
PLPiotr Lampart
Piotr Lampart
SYS. Yershov
S. Yershov
The paper describes results of direct constrained optimization using Nelder-Mead’s method of deformed polyhedron and a Reynolds-averaged Navier-Stokes (RANS) solver to optimize the shape of three-dimensional blading for the exit stage of a large power steam turbine. The computations of the flowfield in the stator and rotor are compressible, viscous, and three-dimensional. Turbulence effects are taken into account using the modified model of Baldwin-Lomax. The objective function is the stage efficiency, with the exit energy considered a loss, and with constraints imposed on the mass flow rate in the form of a penalty function if the mass flow rate falls beyond the required range. The blade sections (profiles) are assumed not to change during the optimization. Two optimization tasks are reported in this paper, first—optimizing the stator straight and compound circumferential lean, and also stator and rotor stagger angles to keep the flow rate unchanged, giving a total number of optimized parameters equal to 5; second—optimizing the stator straight and compound axial sweep, also with stator and rotor stagger angles, also giving five optimized parameters. The process of optimization is carried out for a nominal load; however, due to the fact that exit stages of steam turbines operate over a wide range of flow rates away from the nominal conditions, the original and final geometries are also checked for low and high loads. The process of optimization gives new designs with new three-dimensional stacking lines of stator blades, and with significantly increased efficiencies, compared to the original design, at least for a larger part of the assumed range of load.