1 May 2020 in Geotechnical Testing Journal
The tensile strength of soil is often neglected. Because of the presence of matric suction, unsaturated soils may have substantial tensile strengths with implications for a range of geotechnical problems, such as slope stability, bearing capacity, and the integrity of clay liners. Direct measurement of the tensile strength of soils is complex to carry out, while the simplicity of the Brazilian tensile strength (BTS) test offers an attractive alternative. However, this method was developed to measure the tensile strength of brittle materials. While suction-bound unsaturated soils may behave in a brittle fashion at low moisture contents, such materials become more ductile as the moisture content increases. This study investigated the application of the BTS test to measure the tensile strength of unsaturated soil samples over a range of moisture contents. Because of the low sample strength of these soils, the use of curved loading platens is recommended. The required load angle depends on the ratio between the compressive and tensile strength of the material tested. When brittle behavior is obtained during testing, conventional interpretation may be used, i.e., the maximum mobilized load during load application is used for tensile strength calculation. This is not appropriate when testing ductile materials. During load application on ductile samples, the initial mobilized load-deformation behavior is approximately linear and becomes nonlinear when tensile yielding starts to occur, originating from the sample center where the full tensile strength is first mobilized. It is recommended that, to obtain a conservative estimate of tensile strength, the inflection point where behavior becomes nonlinear should be taken as representative of soil tensile strength.
1 January 2024 in Canadian Geotechnical Journal
A study aimed towards assessing the variation in shaft capacity of piled foundations in swelling clays is presented. At the clay's in-situ water content, the results of pull-out tests on short-length piles revealed no dependency of shaft capacity on overburden stress. Conversely, after achieving a targeted value of swell, a strong dependency on overburden stress was observed. In upper portions of the profile where swell can occur relatively freely, swell-induced softening results in a reduction in pile shaft capacity. However, at greater depths where swell is largely suppressed, so too are the effects of swell-induced softening. For this reason, shaft capacity at depth was found to remain relatively constant before and after swell. The results of an instrumented pile test revealed an overriding dependency of lateral induced swell pressure on the magnitude of heave which has occurred. Irrespective of the level of overburden stress, lateral pressures against the pile were found to increase at early stages of the swelling process, but then reduce as swell continued and softening began to occur. Such a result highlights the importance of carefully considering the level of swell at which shaft capacity should be assessed if a conservative design is to be obtained.
24 April 2023 in E3S Web of Conferences
The hydromechanical properties of a South African expansive clay are reported. In this study,swell potential and swell pressure were assessed by two oedometric approaches, namely, the loading after wetting test and the wetting after loading test. The data indicate that predictions of swell pressure from the two approaches remain similar, whereas greater predictions of heave are obtained for the loading after wetting approach. It is also observed that the magnitude of predicted heave from the loading after wetting test is dependent on the soaking stress considered, with greater swell being obtained for lower soaking stresses. Measurements of primary drying and wetting curves illustrate appreciable hysteresis in the intermediate suction range (≈17 MPa). The discrepancy of this finding with that of a previous study is attributed to differences in fabric. Additionally, when examining the volumetric response of a sample subjected to a drying and wetting path, negligible hysteresis is observed when void ratio is plotted as a function of gravimetric water content. Conversely, when the shrinkage/swell curves are plotted in terms of suction, irreversibly volumetric changes are apparent.
24 April 2023 in E3S Web of Conferences
This paper presents the results of element testing and centrifuge modelling to investigate the behaviour of piled foundations in swelling clays. The study revealed that the preparation procedure implemented, was able to retain key hydromechanical properties when compared with undisturbed specimens. Furthermore, the preparation method utilised to create an artificially ‘fissured’ fabric allowed for significant swell magnitudes to be achieved in the centrifuge within a reasonable timeframe. Centrifugetesting illustrated that, at lower magnitudes of swell, increases in lateral pressure against a pile shaft can increase shaft capacity. However, if swell is allowed to continue to large magnitudes, the effects of swellinduced softening tend to dominate, thus resulting in a reduction in shaft capacity. The effects of swellinduced softening are more prominent close to the clay surface where swell is allowed to occur more freely. However, at greater depths where swell is restricted, so too are the effects of swell-induced softening, resulting in local increases in shaft capacity at greater depths.
6 October 2025 in Soils and Rocks
This article presents an investigation into the influence of swell on the behaviour of large-scale free-ended piles installed in an unsaturated expansive clay deposit when subjected to lateral loading. A ‘dry’ pile was founded in a profile kept at natural water content conditions, and a ‘wet’ pile was founded in a profile which was flooded for six months to allow swelling of the clay prior to testing. Load cycles under two different load magnitudes were applied to the piles, followed by monotonic loading to failure. The applied load, pile head displacement and bending strain distributions with depth (determined using fibre Bragg gratings) were recorded during these tests. The behaviour under 113 kN load cycles was similar for the two piles, with the ‘wet’ pile exhibiting marginally stiffer response. This was attributed to a swell-induced increase in lateral stress acting against the pile shaft. Under load cycles of 145 kN and during the monotonic test, the ‘wet’ pile exhibited a substantially softer response and significantly lower ultimate capacity than that of the ‘dry’ pile. This was attributed to the effects of swell-induced softening and the reduced yield stresses in the swelled clay. These phenomena were interpreted with reference to a site investigation programme including seismic continuous surface wave tests and standard penetration tests, as well as some laboratory testing. Effects of local yielding of the bonded material at fissure interfaces upon pile ratcheting during cyclic loading have also been discussed.
8 January 2026 in Géotechnique Letters
Although extensive research and practical experience have established a good understanding of the magnitude of swell in unsaturated expansive clays due to wetting, significantly less is known regarding the time taken for the swelling strains to develop. This paper describes a mathematical model, based on analogies with conventional consolidation theory and the heat equation, to predict the time-dependent volume increase during swelling of an initially unsaturated expansive clay. A series of oedometer tests on a highly expansive clay was performed to determine the coefficients of swell used in the proposed model. The observed oedometer swelling curves showed good agreement with the theoretical relationship. The results were then used to predict swell over time in a layered centrifuge model constructed from the same clay. The predicted heave closely matched the observed result at any time over an 11-year swelling period in prototype time.