1 June 2019 in Journal of Environmental Chemical Engineering
16 October 2015 in RSC Advances
AAAbbas Aghaeinejad-Meybodi
Abbas Aghaeinejad-Meybodi
+2
The main purpose of this work is to present an experimental operating analysis of a silica membrane reactor (MR) for hydrogen production during the methanol steam reforming (MSR) reaction. To implement this performance analysis, a microporous silica membrane is synthesized by a polymeric sol–gel method. To achieve a high quality silica membrane, a new strategy is used for surface modification of the ceramic support, in which particle size control of the boehmite sol is applied. After evaluation of modified alumina supports, the synthesized silica membrane is characterized and its performance is investigated. The performance analysis of the silica membrane in hydrogen purification shows that the H2/N2, H2/CO2 and H2/Ar permselectivity increase sufficiently to 26.18, 22.13 and 29.42, at 200 °C, respectively, so that hydrogen permeance is measured around 1.1 × 10−6 mol m−2 s Pa at the corresponding conditions. These promising results indicate a high quality of silica membrane for hydrogen production in comparison with the literature data. To achieve the initial purpose of this study, the synthesized silica membrane performance is investigated in the MR set up during the MSR reaction for hydrogen production. In this case, silica MR performance is compared with a traditional reactor (TR) in terms of the methanol conversion, hydrogen yield, hydrogen recovery and CO selectivity. The effects of several operating parameters are also investigated on silica MR performance. In general, the silica membrane presents a higher performance with respect to the TR in all ranges of operating parameters. As a specific consequence, a 6% performance enhancement can be obtained by silica MR in compared to the TR system.
30 November 2016 in Journal of Experimental Nanoscience
In this present study, various types of TiO2 nanostructures were synthesised via hydrothermal method from a commercial titanium dioxide. The effects of the initial concentration of titanium dioxide and the reaction time on the morphology of synthesised nanostructures were investigated. The TiO2 nanostructures were calcined at 500 °C and examined for the photocatalytic performance by decomposing formic acid as an organic pollutant. Scanning electron microscopy, transmission electron microscopy, Brunauer–Emmett–Teller and X-ray diffraction were employed to characterise the synthesised TiO2 nanostructures. The outcomes showed more influence of reaction time rather than initial TiO2 concentration on the properties of TiO2 nanostructures. Various TiO2 nanostructures such as, nanorods and nanotubes were fabricated at different initial TiO2 concentrations and reaction times. In addition, the synthesised nanorod structures showed higher photocatalytic activity than the nanotubes. This is owing to the presence of rutile–anatase combined crystalline phases in the nanorod structures.
2 June 2010 in Journal of Applied Polymer Science
1 April 2015 in Applied Surface Science
6 May 2013 in Separation Science and Technology
The objective of this work was to develop a crack-free membrane intermediate layer on tubular ceramic supports via dip-coating. TiO2 submicron powder, Boehmite as a coupling agent, and SiO2 nanopowder as low melting-point sintering aid were used to deposit a thin and crack-free nanocomposite layer onto α-Al2O3 supports. Effects of key parameters such as solid content, number of coated layers, the presence of coupling agent, and a low melting point nanopowder on physicochemical properties like the thickness, microstructure, pore size, pure water flux, and gas permeance of the final modified ceramic supports were investigated. The obtained results showed that after twice coating of support in 3 wt.% bidispersed TiO2-Boehmite suspension, the pore size of the alumina substrate, ∼0.6 micron, was reduced to ∼0.1 by the uniform membrane intermediate layers with low permeation resistance could be prepared. Moreover, by adding SiO2 nanopowder, sintering temperature of intermediate layers decreases considerably (1000 to 700°C).