To achieve global climate protection goals, a reduction of greenhouse gas emissions is necessary. Accordingly, emissions from technical products such as fluid power components must be known over the entire Product Life Cycle. The Product Carbon Footprint (PCF) is used to systematically record the greenhouse gas emissions of a product. For the calculation of a PCF, for each step in the life cycle, the inputs of material and energy have to be identified and analyzed. Within the context of a cradle-to-gate analysis, the focus is on the production phase and upstream processes. In a previous study carried out by the authors, a variety of fluid powered components were evaluated in regards of their greenhouse gas emissions during the production. Challenges that can arise in such accountings are presented in this paper. For example, in many cases the use of database factors is unavoidable due to the lack of primary data. However, determining of exact factors poses a problem that cannot be neglected. It is shown that even with similar preconditions extreme deviations in the results can occur. Examples for such results will be presented and explained. Conclusions are drawn that may also be helpful when accounting products. Furthermore, recommendations are presented on how to deal with the calculation results of third parties.
Teleoperation of mobile machines can have benefits on numerous aspects, including improved safety, enhanced efficiency, and reduced environmental impact. However, effects like increased latency, lack of machine feeling and limited field of view result in challenges for operators. The use of VR-systems with operator head motion tracking could improve its application. This paper presents the investigation of a tele-remote control system, using a VR-visual feedback system including a stereo camera that mimics the operator’s head motion. An operator study was conducted to evaluate the influence of the tele-remote control system. It is shown that the investigated system is able to increase the achieved immersion and thus improve the operability of teleoperated mobile machines.
With the availability of connectivity solutions and a plethora of sensors that were previously unavailable on mobile machines, there exists a wealth of data that has not yet been harnessed to its full potential. Besides use cases like the automation of machines, condition monitoring, and fault detection, knowledge of process data can help in improving the efficiency in the use of machinery. Excavators have a wide range of applications and therefore are of special interest. The research presented in this paper contributes to a deeper understanding of the utilization of a hydraulic excavator in road construction which can be used for optimizing the duty cycle efficiency. For that purpose, a digital twin of an excavator is created and used to classify its various tasks and operation modes. The integration of digital twin technology in construction processes offers a promising pathway for enhancing productivity and decision-making within the industry. A concept for classifying duty cycles of hydraulic excavators in the context of road construction, with a particular emphasis on leveraging the concept of a digital twin for the excavator, is introduced in this paper. During a conducted study, machine data from several sensors is gathered. The data used in this study is obtained from a real-world construction site with various applications of the examined machine. The collected sensor data not only facilitates the classification of these tasks but also offers opportunities for enhancing automation and implementing smart metering functions within the machines. In addition, conclusions will be drawn about the impact of different concepts of classifying duty cycles on the construction site.
Simulations are a widely used tool in the design and optimization of hydraulic systems and a crucial part of virtually representing a hydraulic system as part of digital twins of mobile machines. Typically, the basis of dynamic hydraulic system models are differential equations, derived from conservation laws, complemented with algebraic equations. However, physical effects like friction or fluid compressibility introduce complexity and lead to nonlinear behavior. Accurately capturing these dynamics makes the simulation of hydraulic systems challenging. Some of the parameters describing these equations, for example, diameters or other dimensions can be easily obtained from data sheets or other information provided by component manufacturers. Others may be completely unknown or must be chosen from a known value range. Determining the parameters may require detailed information, expert knowledge, or measurements from component test rigs. When deriving a digital twin for a specific machine from a production series of identical machines, modeling may also need to allow parameter variation for individual specific components, due to wear or the statistical variations occurring in the production process. This would lead to unfeasible effort when methods with manual parameter identification are used. Deploying a process to automatically parameterize the model with parameter identification methods could reduce the implementation effort. The aim of this paper is to review and analyze the possible methods for identifying unknown parameters or parameters that are not easily measurable in the application to fit lumped parameter hydraulic models of mobile machines to process data.