1 February 2018 in Renewable and Sustainable Energy Reviews
TKTulja Bhavani Korukonda
EREaswaramoorthi Ramasamy
31 August 2021 in ACS Applied Materials & Interfaces
Perovskite solar cells (PSCs) based on organic–inorganic hybrid perovskites containing a small fraction of substituted alkali-metal cations have shown remarkable performance and stability. However, the role of these cations is unclear. The thermal- and moisture-induced degradation of FA1–xCsxPbI3 and (FA1–xCsx)1–yRbyPbI3 (where FA represents formamidinium, x, y = 0.1, 0.05) is investigated using in situ photoelectron spectroscopy (PES). Both compositions exhibit superior moisture stability compared with methylammonium lead iodide under 9 mbar of water vapor. Ga Kα hard X-ray PES is used to investigate the composition of the perovskites at depths up to 45 nm into the surface. This allows more accurate quantification of the alkali-metal distribution than is possible using conventional X-ray PES. The addition of RbI results in a fairly homogeneous distribution of both Cs+ and Rb+ in the surface layers (in contrast to surface Cs depletion seen in its absence), together with a marked reduction in surface iodide vacancies. Overall, RbI is found to play a critical role in increasing the thermal stability of FA1–xCsxPbI3 by providing a source of I– that fills iodine vacancy sites in the perovskite lattice, while Rb+ is not substantially incorporated into the perovskite. We suggest that the concomitant increase in ion migration barriers in the surface layers is key to improved PSC performance and long-lasting stability.
23 August 2022 in Journal of Materials Chemistry A
In recent times, mixed-cation metal halide perovskites have shown promising photovoltaic performance, and the long-term stability of these metal halide perovskites has also been considerably improved by incorporating additives into the perovskite precursor. Here, the role of ionic liquid additives in improving the stability of perovskite is investigated by in situ surface sensitive studies. A small amount (0.3 mol%) of 1-octyl-3-methylimidazolium chloride ionic liquid (IL) is incorporated into FA0.9Cs0.1PbI3 (FACs) (where FA represents the formamidinium cation, CH(NH2)2 +). The thermal- and moisture-induced decomposition of FACs and IL-FACs is investigated using near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS). A comparative study of the pristine and IL-incorporated FACs compositions shows that the IL additive prevents the out-diffusion of organic ions (FA+) from the lattice for temperatures up to 100 °C under 9 mbar water vapour and up to 150 °C under UHV conditions. Both compositions exhibit better stability under 9 mbar water vapour (equivalent to ∼30% relative humidity) compared with conventional methylammonium lead iodide (MAPbI3). The champion device fabricated with IL additive exhibits an improved power conversion efficiency (PCE) of 16% compared with the 13% PCE of the pristine FACs sample. Overall, the results suggest that the IL additive acts to improve the device performance as well as the stability of perovskites under thermal annealing in dry environments, but that a careful choice of IL will be necessary for full passivation in wet environments.
1 May 2017 in Solar Energy
EREaswaramoorthi Ramasamy
16 March 2017 in The Journal of Physical Chemistry C
24 March 2022 in ACS Applied Materials & Interfaces
A titanium dioxide (TiO2) compact film is a widely used electron transport layer (ETL) for n–i–p planar perovskite solar cells (PSCs). However, TiO2 sufferers from poor electrical conductivity, leading to high energy loss at the perovskite/ETL/transparent conductive oxide interface. Doping the TiO2 film with alkali- and transition-metal elements is an effective way to improve its electrical conductivity. The conventional method to prepare these metal-doped TiO2 films commonly requires time-consuming furnace treatments at 450–600 °C for 30 min to 3 h. Herein, a rapid one-step laser treatment is developed to enable doping of tantalum (Ta) in TiO2 (Ta-TiO2) and to simultaneously induce the crystallization of TiO2 films from its amorphous precursor to an anatase phase. The PSCs based on the Ta-TiO2 films treated with the optimized fiber laser (1070 nm) processing parameters (21 s with a peak processing temperature of 800–850 °C) show enhanced photovoltaic performance in comparison to that of the device fabricated using furnace-treated films at 500 °C for 30 min. The ambient-processed planar PSCs fabricated under high relative humidity (RH) of 50–70% display power conversion efficiencies (PCEs) of 18.34% and 16.04% for devices based on Cs0.1FA0.9PbI3 and CH3NH3PbI3 absorbers, respectively. These results are due to the improved physical and chemical properties of the Ta-TiO2 films treated by the optimal laser process in comparison to those for the furnace process. The laser process is rapid, simple, and potentially scalable to produce metal-doped TiO2 films for efficient PSCs.