Peter F. Ksiazek

Peter F. Ksiazek

Auto-generated profile, based on publicly available information

Peter F. Ksiazek

Alpha Technologies Ltd., Burnaby, BC, Canada

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 August 2016 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
RPRafael Pena-Alzola
Rafael Pena-Alzola
David Campos-GaonaDavid Campos-Gaona
David Campos-Gaona
PKPeter F. Ksiazek
Peter F. Ksiazek
MOMartin Ordonez
Martin Ordonez
Small wind energy conversion systems (WECSs) are becoming an attractive option for distributed energy generation. WECSs use permanent-magnet synchronous generators (PMSGs) directly coupled to the wind turbine and connected to the grid through a single-phase grid-tie converter. The loading produced on the dc link is characterized by large ripple currents at twice the grid frequency. These ripple currents are reflected through the dc bus into the PMSG, causing increased heating and ripple torque. In this paper, the PMSG inverter is used to control the dc-link voltage. In order to avoid reflecting the ripple currents into the PMSG, the feedback dc-link voltage is passed through a filter. The Butterworth filters, notch filters, antiresonant filter (ARF) and moving average filter (MAF) are considered. For a fair comparison, formulas are provided to tune the filter parameters so that dc-link voltage control will achieve the selected bandwidth. The different filtering options produce different levels of torque ripple reduction. The notch filter, ARF, and MAF obtain the best results and there is a tradeoff between the filter implementation complexity, bandwidth, overshoot, and the torque ripple reduction. Simulations and experiments using a 2.5-kW PMSG turbine generator validate the proposals.

1 January 2014 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PKPeter F. Ksiazek
Peter F. Ksiazek
MOMartin Ordonez
Martin Ordonez
A swinging bus scheme is investigated in this paper to eliminate undesirable low-frequency ripple current reflection in fuel cells. The swinging bus is thoroughly characterized under various loading conditions to establish a behavioral model. As a result, a general control scheme and signal processing for buck- and boost-derived power converters are obtained. A digital filter in the form of a moving averaging filter proves to be a fundamental component of the control loop, a significant practical advancement in control for low-frequency ripple elimination. A formal mathematical demonstration is included and experimental results are presented to validate the technique and illustrate its benefits.

1 May 2018
Verified
Conference Paper
Closed access
RSRifat Alam Siddique
Rifat Alam Siddique
RKRahul Khandekar
Rahul Khandekar
PKPeter Ksiazek
Peter Ksiazek
JWJiacheng Wang
Jiacheng Wang
Totem-pole FC has the potential to achieve high efficiency and power density by using GaN HEMTs as the high-frequency switching device. With the advent of 600-650V rated commercial GaN HEMTs, the totem-pole PFC is expected to emerge as the dominant topology for the front-end of telecom and data center power supplies. Like most bridgeless topologies, totem-pole PFC generates a large amount of common-mode (CM) noise. Especially around the zero-crossings of input line voltage, the noise is very prominent and a huge current spike is also observed in the input current. A few existing works have theorized about the origin of the CM noise and the spike current but they lack the proper explanation to relate these two mutual issues and estimate the influence of different circuit parameters. The objective of this work is to establish the relationship between these two issues, primarily through the investigation of practical waveforms and a modified CM noise model. To facilitate the design of the totem-pole PFC with reduced EMI, a set of mathematical equations are also developed from a proposed equivalent circuit. Finally, the contribution of different circuit parameters on CM noise and spike current generation at zero-crossing is identified and outlined from the analysis of the equivalent circuit.

1 March 2015
Verified
Conference Paper
Closed access
RPRafael Pena-Alzola
Rafael Pena-Alzola
PKPeter Ksiazek
Peter Ksiazek
MOMartin Ordonez
Martin Ordonez
Huai WangHuai Wang
Huai Wang
Frede BlaabjergFrede Blaabjerg
Frede Blaabjerg
Synchronous interleaved boost converters (SIBCs) result in lower ripple currents and bidirectional power flow. The boost topology has a non-minimum phase characteristic, producing instability problems when a large bandwidth is required. Linear controllers inherently limit the boost controller bandwidth, resulting in a slow response. In this paper, state-trajectory control of the SIBC based on boundary control is proposed to provide an outstanding dynamic response during start-up and sudden load changes, close to the physical limit of the system. The proposed controller and derivation provides a rigorous framework that deals with four switching states, and three state equations, resulting in a simple control law with very fast dynamic response. The normalized trajectories for the SIBC are determined in the geometric domain along with the control law. The exact trajectories are used for fast transients, and approximate trajectories are employed for constant frequency in steady-state. Simulation and experimental results are provided to validate the proposed procedures.

1 March 2019
Verified
Conference Paper
Closed access
JHJan Hammer
Jan Hammer
MOMartin Ordonez
Martin Ordonez
PKPeter Ksiazek
Peter Ksiazek
Wide-bandgap (WBG) devices, like devices based on Silicon-Carbide (SiC) and Gallium-Nitride (GaN), incorporate smaller capacitances and thus faster switching dynamics than traditional semiconductor devices. The size of these capacitances reaches the same order of magnitude than the parasitic elements of the printed circuit board (PCB). This has to be addressed effectively, in order to achieve the full potential of WBG devices. A novel methodology is introduced in this work, which helps to predict the effects of parasitic components of the PCB layout on the dynamic behavior of a power switch. The proposed methodology provides a detailed model, which incorporates the parasitic elements of the PCB design. This model is translated into a simple metamodel, using a design-of-experiment (DoE) methodology. With this metamodel, a design-space which utilizes single and multiple parasitic and discrete parameters to predict the impact on the switching behavior is generated. The parasitic parameters are estimated with simple geometry approximations of the PCB design. The obtained metamodel enables PCB designers to map performance objectives of the switching dynamics, such as voltage/current overshoot, to layout parameters before manufacturing. The methodology is validated with simulation and experimental results in the context of the gate-source voltage overshoot of a GaN-prototype, showing high accuracy.

1 September 2014
Verified
Conference Paper
Closed access
PKPeter F. Ksiazek
Peter F. Ksiazek
IZIgnacio Galiano Zurbriggen
Ignacio Galiano Zurbriggen
FPFrancisco Paz
Francisco Paz
JGJuan M. Galvez
Juan M. Galvez
MOMartin Ordonez
Martin Ordonez
A reverse control scheme for modular telecommunications battery chargers with solar panel input is investigated in this paper. Small-signal analysis is performed for a typical state-of-the-art multi-stage converter and the reverse control transfer functions are presented and used to develop a linear control strategy, which is validated using simulations and experimental results.