We constrained the solidus of a model Martian composition with low bulk Mg# (molar MgO/(MgO + FeOT) × 100 ~75) and high total alkali (Na2O + K2O = 1.09 wt.%) concentration at 2 to 5 GPa by experiments. Based on the new solidus brackets, we provide a new parameterization of the solidus temperature as a function of pressure of Martian mantle: Ts(°C) = − 5P (GPa)2 + 107P(GPa) + 1,068. The newly constrained solidus of the Lodders and Fegley (1997; https://doi.org/10.1006/icar.1996.5653) model Martian composition (LF composition) is 20 to 90 °C lower than the previous solidus of model Martian mantle with lower total alkali (~0.54 wt.%). The supersolidus experiments yield an average isobaric melt productivity, dF/dT, of 20 ± 6 wt.%/100 °C. We also bracketed the solidi of model Martian mantle compositions with low Mg# (~75) and low alkali (~0.54 wt.%), and with high Mg# (~80) and low alkali (~0.54 wt.%) at a constant pressure of 3 GPa. We find that bulk Mg# enhances the solidus temperature and bulk total alkalis suppress it. A parameterization that estimates the effect of bulk Mg# and total alkalis on peridotite solidus, including Mars and Earth, at 3 GPa can be described as: Ts(°C) = 4.23Mg # − 85(Na2O(wt. %) + K2O(wt. %)) + 1,120. Based on the new solidus parameterizations, 10–40 km more Martian crust would be produced by columnar decompression melting for LF model composition compared to the low Mg#‐low alkali model composition. The quantitative constraints on the solidus shift with Mg# and total alkalis from this study can be used to assess the Martian mantle solidus change through melting and melt extraction over time and the role of mantle heterogeneity in crustal production.
1 December 2024 in American Mineralogist: Journal of Earth and Planetary Materials
Sulfur (S) in the mantle is conventionally assumed to be exclusively stored in accessory sulfide phases, but recent work shows that the major silicate minerals that comprise >99% of the mantle could be capable of hosting trace amounts of S. Assessing the incorporation of trace S in nominally S-free mantle minerals and determining equilibrium S partitioning between these minerals and basaltic melt requires analyzing small experimental phases with low S contents. Here, we develop a protocol for EPMA analysis of the trace levels of S in silicate phases. We use a suite of natural and experimental basaltic glass primary and secondary standards with S contents ranging from 44 ppm to 1.5 wt%. The effects of beam current and counting time are assessed by applying currents ranging from 50 to 200 nA and total counting times between 200 and 300 s at 15 kV accelerating voltage. We find that the combination of 200 nA beam current with a 200 s counting time (80 s peak, 60 s each for upper and lower background, respectively) achieves precise yet cost-effective measurements of S down to a calculated detection limit of ~5 ppm and a blank-derived, effective detection limit of ~17 ppm. Close monitoring of the S peak intensity and position throughout the duration of each spot also shows that high currents and extended dwell times do not compromise the accuracy of measurements, and even low S contents of 44 ppm can be reproduced to within one standard deviation. Using our developed recipe, we analyzed a small suite of experimental clinopyroxenes (Cpx) and garnets (Gt) from assemblages of silicate partial melt + Cpx ± Gt ± sulfide, generated at 1.5 to 3.0 GPa and 1200 to 1300 °C. We find S contents of up to 71 ± 35 ppm in Cpx and 63 ± 28 ppm in Gt and calculate mineral-melt partition coefficients (Dsmin/melt) of up to 0.095 ± 0.064 and 0.110 ± 0.064 for DsCpx/melt and DsGt/melt, respectively. The sulfur capacity and mineral-partitioning for Cpx are in good agreement with SXRF measurements in a prior study by Callegaro et al. (2020), serving as an independent validation of our EPMA analytical protocol.
27 June 2026 in Journal of Geophysical Research: Solid Earth