Reconfigurable intelligent surface (RIS) becomes an increasingly important technology in sixth-generation (6G). The key aspect of RIS is smartly configuring the wireless propagation environment and providing supplementary links to enhance the signal transmission between the BS and the UE. In recent years, there has been a surge of interest in RISs in joint active and passive beamforming design to improve the system performance of RIS-assisted systems with the assumption of uncorrelated environments. To date, far too little attention has been paid to the situations that consider the correlations among the antennas and RIS reflecting elements. In this article, we focus on an RIS-assisted multiple-input multiple-output (MIMO) system under spatial fading correlations, with the statistical channel state information (CSI) known at the transmitter and the RIS. We aim to maximize the ergodic spectral efficiency (SE) of this system. At first, we derive a tight upper bound on the ergodic SE. Concise upper bounds are also shown in special cases of independent and identically distributed (i.i.d.) Rician and Rayleigh, correlated Rayleigh as well as extreme Rician MIMO channels. Next, we propose a benchmark algorithm based on the semidefinite relaxation (SDR) technique to jointly optimize the beamforming vector at the transmitter and phase shift matrix of the RIS. Alternative manner is utilised until both arrive at convergence. Furthermore, we apply the dominant eigen direction transmission scheme to do beamforming in order to reduce the complexity of the algorithm, and consider the column control of the RIS to facilitate practical hardware implementation. Numerical results show the tightness of the upper bounds and the effectiveness of our proposed algorithm for improving the ergodic SE as well as the effects of freedom degrees on performances.
26 November 2020 in IEEE Transactions on Communications
The combination of orthogonal frequency modulation (OFDM) and multiple-input multiple-output (MIMO) systems plays an important role in modern communication systems. In order to meet the growing throughput demands, future MIMO-OFDM receivers are expected to utilize a massive number of antennas, operate in dynamic environments, and explore high frequency bands, while satisfying strict constraints in terms of cost, power, and size. An emerging technology to realize massive MIMO receivers of reduced cost and power consumption is based on dynamic metasurface antennas (DMAs), which inherently implement controllable compression in acquisition. In this work we study the application of DMAs for MIMO-OFDM receivers operating with bit-constrained analog-to-digital converters (ADCs).We present a model for DMAs which accounts for the configurable frequency selective profile of its metamaterial elements, resulting in a spectrally flexible hybrid structure. We then exploit previous results in task-based quantization to show how DMAs can be configured to improve recovery in the presence of constrained ADCs, and propose methods for adjusting the DMA parameters based on channel state information. Our numerical results demonstrate that the DMA-based receiver is capable of accurately recovering OFDM signals. In particular, we show that by properly exploiting the spectral diversity of DMAs, notable performance gains are obtained over existing designs of conventional hybrid architectures, demonstrating the potential of DMAs for MIMO-OFDM setups in realizing high performance massive antenna arrays of reduced cost and power consumption.
1 January 2020 in IEEE Transactions on Wireless Communications
The order-of-magnitude increase in the dimension of antenna arrays, which forms extra-large-scale massive multiple-input-multiple-output (MIMO) systems, enables substantial improvement in spectral efficiency, energy efficiency, and spatial resolution. However, practical challenges, such as excessive computational complexity and excess of baseband data to be transferred and processed, prohibit the use of centralized processing. A promising solution is to distribute baseband data from disjoint subsets of antennas into parallel processing procedures coordinated by a central processing unit. This solution is called subarray-based architecture. In this work, we extend the application of expectation propagation (EP) principle, which effectively balances performance and practical feasibility in conventional centralized MIMO detector design, to fit the subarray-based architecture. Analytical results confirm the convergence of the proposed iterative procedure and that the proposed detector asymptotically approximates Bayesian optimal performance under certain conditions. The proposed subarray-based EP detector is reduced to centralized EP detector when only one subarray exists. In addition, we propose additional strategies for further reducing the complexity and overhead of the information exchange between parallel subarrays and the central processing unit to facilitate the practical implementation of the proposed detector. Simulation results demonstrate that the proposed detector achieves numerical stability within few iterations and outperforms its counterparts.
24 January 2019 in IEEE Transactions on Communications
The use of low-resolution analog-to-digital converters (ADCs) can significantly reduce power consumption and hardware cost. However, their resulting severe nonlinear distortion makes achieving reliable data transmission challenging. For orthogonal frequency division multiplexing (OFDM) transmission, the orthogonality among subcarriers is destroyed. This invalidates conventional OFDM receivers relying heavily on this orthogonality. In this study, we move on to quantized OFDM (Q-OFDM) prototyping implementation based on our previous achievement in optimal Q-OFDM detection. First, we propose a novel Q-OFDM channel estimator by extending the generalized Turbo (GTurbo) framework formerly applied for optimal detection. Specifically, we integrate a type of robust linear OFDM channel estimator into the original GTurbo framework, and derive its corresponding extrinsic information to guarantee its convergence. We also propose feasible schemes for automatic gain control, noise power estimation, and synchronization. Combined with the proposed inference algorithms, we develop an efficient Q-OFDM receiver architecture. Furthermore, we construct a proof-of-concept prototyping system and conduct over-the-air (OTA) experiments to examine its feasibility and reliability. This is the first work that focuses on algorithm design system implementation in the field of low-resolution quantization communication. The results of the numerical simulation and OTA experiment demonstrate that reliable data transmission can be achieved.
Transferring objects from one place to another place is a common task performed by human in daily life. During this process, it is usually intuitive for humans to choose an object as a proper container and to use an efficient pose to carry objects; yet, it is non-trivial for current computer vision and machine learning algorithms. In this paper, we propose an approach to jointly infer container and human pose for transferring objects by minimizing the costs associated both object and pose candidates. Our approach predicts which object to choose as a container while reasoning about how humans interact with physical surroundings to accomplish the task of transferring objects given visual input. In the learning phase, the presented method learns how humans make rational choices of containers and poses for transferring different objects, as well as the physical quantities required by the transfer task (e.g., compatibility between container and containee, energy cost of carrying pose) via a structured learning approach. In the inference phase, given a scanned 3D scene with different object candidates and a dictionary of human poses, our approach infers the best object as a container together with human pose for transferring a given object.