Srđan Mladenović

Srđan Mladenović

Auto-generated profile, based on publicly available information

Srđan Mladenović

Faculty of Mechanical Engineering, University of Niš, Niš, Serbia

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2018 in Journal of Healthcare Engineering
Verified
Journal Article
Open access
PDF file
Nikola M. VitkovicNikola M. Vitkovic
Nikola M. Vitkovic
SMSrđan Mladenović
Srđan Mladenović
MTMilan Trifunović
Milan Trifunović
MZMilan Zdravković
Milan Zdravković
MMMiodrag Manić
Miodrag Manić
JMJelena Mitić
Jelena Mitić
Computer-Assisted Orthopaedic Surgery (CAOS) defines a set of techniques that use computers and other devices for planning, guiding, and performing surgical interventions. The important components of CAOS are accurate geometrical models of human bones and plate implants, which can be used in preoperational planning or for surgical guiding during an intervention. Software framework which is introduced in this study is based on the Model-View-Controller (MVC) architectural pattern, and it uses 3D models of bones and plate implants developed by the application of the Method of Anatomical Features (MAF). The presented framework may be used for preoperative planning processes and for the production of personalized plate implants. The main idea of the research was to develop a novel integrated software framework which will provide improved personalized healthcare to the patient, and at the same time, provide the surgeon with more control over the patient’s treatment and recovery.

1 January 2014 in Serbian Journal of Management
Verified
Journal Article
Open access
PDF file
DPDragan Pavlović
Dragan Pavlović
MRMilena Nebojsa Rajic
Milena Nebojsa Rajic
SMSrdjan Mladenovic
Srdjan Mladenovic
PMPedja Milosavljevic
Pedja Milosavljevic
This paper presents a methodology for applying the Lean Six Sigma method on the educational process. After defining defects that have negative influence on the final quality evaluation of higher education and how these defects can be remedied, the Pareto analysis is done, and that is used for establishing a vital minority of the exams that are critical for examination of faculty. The next step is the Statistical Process Control (SPC) analysis that is performed on the exams that are classified as vital minority in Pareto analysis. Ishikawa diagram shows a relation between considered consequence (small number of passed exams) and all factors that influence this consequence. Based on the results of implementation of the Lean Six Sigma method in the educational process and implementation of all suggested improvements, the comparative overview of Pareto analysis is given for 2009/2010 and 2012/2013 academic year at the Faculty of Mechanical Engineering, University of Niš.

29 July 2019 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
PJPredrag Janković
Predrag Janković
Miloš MadićMiloš Madić
Miloš Madić
MRMiroslav Radovanović
Miroslav Radovanović
DPDusan Ljubomir Petković
Dusan Ljubomir Petković
SMSrđan Mladenović
Srđan Mladenović

1 July 2014 in Journal of Medical Biochemistry
Verified
Journal Article
Open access
PDF file
VSVojislav Stoiljković
Vojislav Stoiljković
PMPedja Milosavljevic
Pedja Milosavljevic
SMSrđan Mladenović
Srđan Mladenović
DPDragan Pavlović
Dragan Pavlović
MRMilena Nebojsa Rajic
Milena Nebojsa Rajic
Laboratories that are part of clinical centers are faced with the inevitability that their efficiency must be on a high level. Most of the biochemical laboratories are automated, but they are still underperforming. The best approach to increase the efficiency or to improve the processes today is the Lean Six Sigma methodology. This methodology extracts many benefits from automated processes. A lean process in the laboratory focuses on the time cycle to obtain results and reduce costs, or both components at the same time. Six Sigma methodology provides that the processes take place in the laboratory without delays and defects. The process that takes place at the Center for Medical Bio - chemistry (CMB) can be divided into two parts: the first part takes place in the receiving infirmary (pre-analytics) and the second part takes place at the offices of the CMB from the receipt of samples (analytics) to obtained results. The paper observes both processes, identifies critical areas where they come to a halt, defines access and reviews the results obtained using the Lean Six Sigma methodology. By applying Lean tools, the places that do not add value and those that significantly increase the cycle time were identified. This paper presents the results obtained without going into detail about the application of these Lean tools.

2 August 2016 in Facta Universitatis, Series: Mechanical Engineering
Verified
Journal Article
Open access
PDF file
SMSrđan Mladenović
Srđan Mladenović
PMPedja Milosavljevic
Pedja Milosavljevic
NMNevena Milojević
Nevena Milojević
DPDragan Pavlović
Dragan Pavlović
MRMilena Nebojsa Rajic
Milena Nebojsa Rajic
In the last twenty years, many companies have realized that the demands of the global market, including more demanding and receptive customers, have set new standards for production flexibility. Gradual reduction of mass production, characteristic of a large number of companies, has opened space for the introduction of a new system which focuses exclusively on the customer. The customer-oriented system was created with the idea that process optimization would lead to the production of a relatively cheap product, delivered on time and with the best possible quality. Such a system is achieved by applying the Lean Six Sigma concept. The aim of this paper is to identify all of the defects that occur as losses and complicate the process of production in order to achieve the Lean Six Sigma level in the Shinwon Company. The original data from the Shinwon company were identified, collected and analyzed, using the methods and tools of the Lean Six Sigma concept (Process Mapping, 5S audit, Pareto diagram, Ishikawa diagram, Seven basic wastes and SPC analysis), in order to present the effectiveness of the quality management system and to evaluate the possibility of its continuous improvement.

1 October 2020 in Advanced Technologies & Materials
Verified
Journal Article
Closed access
SRSaša Ranđelović
Saša Ranđelović
MMMladomir Milutinović
Mladomir Milutinović
VBVladislav Blagojevic
Vladislav Blagojevic
SMSrđan Mladenović
Srđan Mladenović
DTDejan Tanikić
Dejan Tanikić
In the industrial processes of injection molding, one of the basic requirements is a uniform temperature filed within workpiece and the mold cavities. In the case of simple geometry of workpiece and mold with single cavity achieving a uniform temperature field is not a critical issue. However, if one deals with parts of complex geometries, multi-cavity molds and asymmetric layout of different forms in the mold additional analyses of the runner and cooling system are necessary in order to obtain the required quality and accuracy of end the products. Disposition and dimensions of both runners and cooling channels are directly related to the geometry of finished parts and material properties. In that sense, virtual models and numerical simulations of injection molding processes based on the finite element method are very effective tool which enable accurate prediction of potential problems and significant reduction of trial and error procedure. In this paper, FEM software package Moldex3D was employed for simulation and analyses of injection molding process in which pipe fittings Ø75/45o and Ø75/90o are produced using a mold with two asymmetric cavities.