Young Mook Yun

Young Mook Yun

Auto-generated profile, based on publicly available information

Young Mook Yun

Professor, Dept. of Civil Engineering, Kyungpook National Univ., Daegu 702-701, Korea

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2008 in Journal of Structural Engineering
Verified
Journal Article
Closed access
YYYoung Mook Yun
Young Mook Yun
BKByung Hun Kim
Byung Hun Kim
Although approaches implementing strut-tie models are valuable tools for designing disturbed regions of structural concrete, the provisions of current design codes have to be improved because of uncertainties in terms of the selection of the strut-tie model and the structural type of strut-tie model. To improve the uncertainties, a grid strut-tie model approach is presented in this study. The presented approach, which allows for a consistent and effective design of structural concrete, employs a single type of grid strut-tie model whereby various load combinations can be considered. In addition, the approach performs an automatic selection of an optimal strut-tie model by evaluating the capacities of struts and ties using a simple optimization algorithm. The validity and effectiveness of the presented approach is verified by conducting the analyses of the eight reinforced concrete deep beams tested to failure and the design of the shear wall with two openings.

1 December 2011 in Advances in Structural Engineering
Verified
Journal Article
Closed access
BKByung-Hun Kim
Byung-Hun Kim
YYYoung-Mook Yun
Young-Mook Yun
The ultimate strength of simply supported reinforced concrete deep beams is governed by the capacity of the shear resistance mechanism. The structural behavior of the deep beams is controlled mainly by the mechanical relationships between the primary design variables including shear span-to-effective depth ratio, flexural reinforcement ratio, and the compressive strength of concrete. In this study, a simple indeterminate strut-tie model which reflects all characteristics of the ultimate strength and behavior of the deep beams was presented. A load distribution ratio, defined as the fraction of load transferred by a truss mechanism, was also proposed to help structural designers perform the rational design of deep beams by using the strut-tie model approaches of current design codes. In the determination of the load distribution ratio, a concept of balanced shear reinforcement ratio which ensures the ductile shear design of the deep beams was introduced, and the effect of the primary design variables was reflected through numerous numerical analyses of the presented indeterminate strut-tie model. In the companion paper, the validity of the presented model and load distribution ratio was examined by applying them to the evaluation of ultimate strength of 234 simply supported reinforced concrete deep beams tested to failure.

1 November 2006 in Journal of Structural Engineering
Verified
Journal Article
Closed access
YYYoung Mook Yun
Young Mook Yun
A strut–tie model approach has proven to be useful for the detailing of disturbed regions of structural concrete. This approach promotes a better understanding of force transfer mechanisms and improves the designer’s ability to handle unusual circumstances. Despite the advantages of the strut–tie model approach, portions of them lack adequate definition and have not been extensively verified for use in structural analyses and designs. One of the specific areas in which further research is required is nodal zones. Before the strut–tie model approach can be practically implemented into various regions of structural concrete, a proper way of checking the strength limits of nodal zones to allow safe transfer of strut and tie forces through nodal zones must be established. In this study, a literature review of the approaches for evaluating the limits of nodal zone strength was conducted, and a consistent and general approach applicable to any type of strength verification situation of two-dimensional nodal zon...

1 November 2016 in Journal of Structural Engineering
Verified
Journal Article
Closed access
YYY. M. Yun
Y. M. Yun
JRJ. A. Ramirez
J. A. Ramirez
The design of structural concrete using strut-tie models requires establishing the effective strength of concrete struts, ensuring sufficient anchorage of reinforcing bars in nodal zones, and the geometric compatibility of the strut-tie model within the member geometry. In this paper, a consistent and general method applicable to three-dimensional (3D) strut-tie models is presented. The proposed method includes the effects of 3D stresses associated with tensile strains in reinforcing bars crossing a strut, strut length, deviation angle between strut orientation and compressive principal stress flow, compressive strength of concrete, and degree of confinement provided by reinforcement. The proposed method is implemented and then verified using data from 115 reinforced concrete pile caps tested to failure.

23 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
SPSung-sik Park
Sung-sik Park
SWSeung-wook Woo
Seung-wook Woo
JLJung-Shin Lee
Jung-Shin Lee
YYYoung-Mook Yun
Young-Mook Yun
Dong-Eun LeeDong-Eun Lee
Dong-Eun Lee
Annual coffee consumption has increased to 10 million tons. Of the coffee consumed, 65% is discarded as spent coffee grounds (SCG). However, most SCG are buried in the ground as organic waste. The more coffee consumption increases, the more land is used for disposing of spent coffee. SCG recycling has gotten considerable attention as a solution involved in these issues. The construction community has studied means and methods to recycle SCG as construction materials, such as bricks, subgrade fillers, thermal insulators, etc. This paper presents a new method, which recycles SCG as a construction material, maximally using its acidity. The SCG were hardened with natural binders (i.e., animal glue (AG) and starch (S)) and red clay (RC). The SCG mixtures were pressed with 2 MPa in a cylindrical mold and cured for 7 days. Then, the strength, durability, and pH tests were measured. The AG- and RC-treated SCG sample, which outputs 1933 kPa of strength and a 4.9 pH value, is identified as the optimal sampling method among the acid materials produced in this study. The optimal sample decreases the pH to approximately 7 of water where 68% weight of Ordinary Portland cement was soaked in.

8 May 2019 in Advances in Structural Engineering
Verified
Journal Article
Closed access
PDF file
YYYoung Mook Yun
Young Mook Yun
HCHyun Soo Chae
Hyun Soo Chae
The failure behavior of a reinforced concrete corbel is complicated due to the shear span-to-effective depth ratio, reinforcement patterns, load conditions, and material properties. In this study, an optimum first-order indeterminate strut-and-tie model that reflects all characteristics of the failure behavior is proposed for the rational design of reinforced concrete corbels with a shear span-to-effective depth ratio of less than 1.0. A load distribution ratio that transforms the indeterminate strut-and-tie model into a determinate model is also developed to help structural designers design reinforced concrete corbels using the strut-and-tie model methods of current design codes. For the development of the load distribution ratio, a material nonlinear finite element analysis of the proposed first-order indeterminate strut-and-tie model was conducted repeatedly by changing the combination of primary design variables of the corbels. To examine the validity of our results, the ultimate strengths of 294 reinforced concrete corbels tested to failure by other investigators were predicted using the proposed strut-and-tie model with the load distribution ratio, the existing determinate strut-and-tie models representing arch and truss load transfer mechanisms, and the American Concrete Institute 318 conventional design method based on a shear friction theory. The ultimate strengths predicted by the proposed strut-and-tie model agreed fairly well with the experimental results. The ratio of the experimental strength to the predicted strength (and coefficient of variation) was 1.09 (28.0%), implying that the proposed strut-and-tie model can represent the load transfer mechanisms of corbels most appropriately.